This paper reviewed the application of parametric building information modelling (BIM) in bridge engineering, highlighting its contributions to improving workflows, fostering interdisciplinary collaboration, enhancing interoperability, and optimizing design processes. It examined how parametric modeling facilitated rapid design exploration and simulation-driven optimization through flexible, rule-based relationships. Case studies illustrated the use of parametric techniques to create customizable bridge components and assemblies, which enhanced decision-making through seamless integration with analysis tools. Furthermore, this study discussed forward design, an emerging trend that improved collaboration efficiency and cost control by establishing early computational definitions, as opposed to following traditional document-driven design methods. It also emphasized the importance of open standards, such as Industry Foundation Classes (IFC), for information exchange, noting the need to extend these standards for specialized infrastructure domains. Finally, it outlined future research directions, including scalability, multimodal data integration, and generative design, aiming to fully leverage the potential of BIM throughout the lifecycle of bridges.
Concrete-filled hollow steel (CFHS) has become more popular due to its advantages and benefits compared to reinforced concrete. This paper presents the experimental investigation on the performance of rubberized pozzolanic concrete-filled hollowsteel column (RuPCFHS) under monotonic and cyclic lateral load in comparison to bare hollow steel column and normal concrete-filled hollow steel column (NCFHS). The test parameters included the type of concrete infill and the level of axial load. Modified rubberized pozzolanic concrete with comparable compressive strength to that of normal concrete was used. Two types of axial load conditions: no axial load and 20% axial load were considered in the testing. The test results indicate that the performance of the columns improved when concrete infill was introduced in the hollow steel. The application of axial loading also increased the capacity of the column specimens. RuPCFHS behaved with comparable performance with NCFHS in both monotonic and cyclic testing. RuPCFHS recorded the highest increment in the energy dissipation capability when 20% axial load was applied to the column when compared to the other specimens. The comparable performance indicated the possibility ofRuPC as an infill material of CFHS andRuPCFHS as a structural component.
The impact of climate change towards water surface resources is crucial, particularly in developing and non-developing countries. Groundwater as a main water resource is thus an essential. However, contamination due to hydrocarbon spills affects the groundwater as a water resource, especially as a main source of drinking water. This chapter investigates the light non-aqueous phase liquid (LNAPL) penetrations in double-porosity soil with different moisture contents and with or without vibration impact. It also explains the LNAPL penetration phenomena by employing image analysis. The physical laboratory experiments were implemented using an acrylic cylinder, a mirror, toluene and a Nikon D90 DSLR digital camera. Prepared soil was poured in an acrylic cylinder and compressed with compressor until it became 10 cm in height. LNAPL was then poured instantaneously onto the acrylic cylinder that was filled with soil sample. The LNAPL penetration patterns were recorded and monitored using a Nikon D90 DSLR digital camera. The processing technique was conducted at predetermined time intervals using Surfer software and Matlab routine to plot the LNAPL pattern. The results showed that a higher penetration rate of LNAPL occurred with higher moisture content and without vibration impact. The penetration time for LNAPL to reach the bottom of the soil sample was found to be longer for the soil that had low moisture content and with vibration impact.
30 September 2024 in Journal of Sustainable Civil Engineering and Technology
The Steel Plate Shear Wall (SPSW) is widely used as a lateral force resisting system in areas prone to high seismic activity. This is because of its exceptional ductility and ability to dissipate energy. Previous studies have indicated that disconnecting the infill plate from the Vertical Boundary Element (VBE) can decrease the demands on the column. The observed outcomes lead to a decline in both the energy dissipation capability and the lateral load-bearing capacity. The primary goal of this investigation is to mitigate stress on the column while concurrently reducing both the energy dissipation and lateral force capacities. To accomplish this, a partial connection will be established between the infill plate and the Vertical Boundary Element. Thus, the overarching objective of this research is to identify the optimal connection length that minimizes the demands on the column while simultaneously curtailing the reduction in energy dissipation and lateral force capacities. Using Abaqus software, twenty models with different infill plate thicknesses and lengths of connection between the infill plate and Vertical Boundary Element were analysed. To determine the optimal length of connection between the infill plate and Vertical Boundary Element, the energy dissipation capacity, lateral load capacity, and column stresses were evaluated and compared. The maximum dissipation of energy occurs at a connection length of 75% between the infill plate and Vertical Boundary Element and an infill plate thickness of 12 mm. In contrast, the greatest lateral load capacity is achieved at connection lengths of 50% between a 25 mm infill plate thickness and a Vertical Boundary Element weight of 25%. The column stress reaches its minimum value when the infill plate measures 20 and 25 mm, and it reaches its maximum value when the infill plate measures 6 mm and 12 mm. By increasing the thickness of the infill plate and minimizing its connection to the Vertical Boundary Elements, the column stress in Vertical Boundary Elements can be decreased, while simultaneously enhancing lateral load capacity and maintaining an adequate level of energy dissipation.