Energy-efficient buildings require materials with low thermal conductivity, and high fire resistance and mechanical properties. Traditional chitosan aerogel is limited by its poor fire resistance and silica aerogel is either brittle or displays a high thermal conductivity. Herein, we report a dual-modified aerogel with high mechanical properties, low thermal conductivity, and excellent fire resistance. Briefly, the chitosan-derived silica aerogel (CA) was first fabricated, followed by loading varying contents of phytate-piperazine (PPA) intumescent flame-retardant. This well-designed aerogel (CA/PPA) combines with the high mechanical strength of chitosan aerogel, the excellent fire resistance function of silica aerogel, and the intumescent flame-retardant performance of PPA. The as-created CA/PPA-2.0 exhibited enhanced mechanical properties, as evidenced by the fact that its compressive strength rose from 1.3 ± 0.10 to 2.9 ± 0.23 MPa at 90.0% strain compared to that of neat chitosan aerogel. Additionally, compared to CA, the CA/PPA aerogel with 2.0 wt% PPA exhibits significant fire safety performance. For instance, the peak heat release rate, total heat release, maximum average rate of heat emission, and thermal conductivity were reduced by 62.1%, 55.6%, 48.4%, and 12.5%, respectively. In addition, the CA/PPA-2.0 composite aerogel also exhibits a fire-alarm performance under flame attack. This work introduces a feasible strategy to produce high-performance aerogels with promising applications in construction, aerospace, and thermal insulation.
29 November 2023 in Journal of Analytical and Applied Pyrolysis
The high-pressure polyethylene process uses cyclone separators to separate ethylene gas, polyethylene, and its oligomers. The oligomers larger than 10 microns that cannot be separated must be filtered through a filter to prevent them from entering the compressor and affecting its normal operation. When the separation efficiency of the cyclone separator is low, the filter must be cleaned more frequently, which will reduce production efficiency. Research shows that improving the separation efficiency of the separator is beneficial for the separation of small-particle oligomers and reduces the frequency of filter cleaning. For this reason, Computational Fluid Dynamics simulations were performed for 27 sets of cyclone separators to determine the effects of eight structural factors (cylinder diameter, cylinder height, cone diameter, cone height, guide vane height, guide vane angle, exhaust pipe extension length, and umbrella structure height) on separation efficiency and pressure drop. The equations for separation efficiency and pressure drop using these eight factors and the equations based on energy-efficiency parameters were determined. The optimization analysis showed that separation efficiency can be improved by 98.7% under the premise that the pressure drop is only increased by 8.2%. By applying the improved structure to the high-pressure polyethylene process, separation efficiency is increased by 17.7%, which could effectively reduce the frequency of filter cleaning for this process, and thereby greatly improve production efficiency.
Within the realm of industrial energy conservation, the optimization of heat exchanger performance is paramount for the augmentation of energy utilization efficiency. This investigation employs computational fluid dynamics (CFD) simulations to elucidate the effects of an innovative DNA-Inspired Slotted Insert (DSI) on the convective heat transfer and pressure drop characteristics within heat exchange tubes. The study provides a thorough analysis of fully turbulent flow (Re = 6600–17,200), examining the effects of various DSI pitches, key lengths, and geometries. The findings reveal that the DSI instigates a three-dimensional spiral flow pattern, which is accompanied by an escalation in the Nusselt number (Nu) and friction factor (f) with increasing Reynolds numbers. An inverse relationship between Nu and both pitch and key length is observed; conversely, f exhibits a direct correlation with these parameters. The study identifies an optimal configuration characterized by a pitch of 10 mm and a key length of 1.5 mm, with square keys demonstrating superior heat transfer performance relative to other geometrical configurations. This research contributes significant design and application insights for double-helical inserts, which are pivotal for the enhancement of heat exchanger efficiency.
A Laval nozzle is a pivotal component of supersonic separation technology for dehydration, but its performance is constrained by low separation efficiency due to intractable conflicts between droplet nucleation and growth rates. To address this issue, this work for the first time applied the Foelsch-MOC method to design an expansion section with a first-order differentiable and second-order continuous profile. A numerical model for pure water vapor condensation based on the ideal gas equation of state (EOS) was then established to optimize nozzle structures for droplet growth. Major findings revealed that the droplet radius of the Foelsch-MOC nozzle was 30.5% higher than that of the conical nozzle, while its outlet liquid mass fraction was 5.8% lower. The liquefaction capacity was found to increase first and then decrease with the expansion coefficient, peaking at 0.5. Moreover, increasing the axis shift from 9.3 mm to 25 mm promoted the outlet liquid mass fraction by 1.2% and decreased the droplet radius by 9.3%, thereby improving liquefaction capacity. These results highlight the droplet growth superiority of the novel expansion profile, providing a valuable guideline for designing nozzles that simultaneously ensure liquefaction efficiency and facilitate droplet development.