The conversion of fatty acids into bio-hydrocarbons can be carried out through a deoxygenation (DO) reaction. Catalytic deoxygenation of fatty acids can occur through three reaction pathways: decarbonylation, decarboxylation, and hydrodeoxygenation. In this study, three kinds of silica were prepared: (i) silica obtained from the rice husk ash (RHA); (ii) synthetic mesoporous silica SBA-16; and (iii) commercial silica. All prepared silica was used as supported nickel (Ni) catalyst for bio-hydrocarbon production through DO reaction of oleic acid. The objective of this study was to investigate the effect of variations of silica on the reaction pathway and final products composition of DO reaction of oleic acid. The catalysts were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), surface area analysis, and NH3-temperature-programme desorption. Based on XRF and XRD analysis results, it can be concluded that nickel was successfully impregnated into all silica. All samples of catalysts were used in a reaction carried out at temperature of 285 °C under a pressure of 40 bar H2 for 2h. The results showed that all catalysts were able to convert oleic acid to bio-hydrocarbon with differences in products composition. The highest oleic acid conversion of 98.25% was achieved with Ni/RHA catalyst but the obtained liquid products was the lowest among other catalysts. It is found that this phenomenon was closely related to the acidity properties of the catalyst.
7 October 2025 in Bulletin of Chemical Reaction Engineering & Catalysis
The solvent-free hydrogenolysis (HDL) of benzyl phenyl ether (BPE), a model for the C–O (α-O-4) linkage in lignin, was investigated using NiMo-pillared clay catalysts in their reduced (NiMoPR) and sulfided (NiMoPS) forms. NiMoPS show higher activity and selectivity to give an equimolar mixture of toluene and phenol, demonstrating selective cleavage of the Caliphatic–O of BPE, while non-equimolar amounts were found for NiMoPR. Strong acid sites are dominant in NiMoPS, giving a higher total acidity compared to NiMoPR, which explains the higher selectivity of the sulfided catalyst towards the HDL products and monomeric aromatics. To understand the interaction of BPE on the catalyst surface, we carried out a comprehensive investigation of the 2D potential energy surface (PES) of BPE and the vibrational spectra using neutron scattering and computational studies. The results suggest that BPE is weakly adsorbed on NiMoPS and the pillared clay support (PILC) via a van der Waals or H-bonding interaction, but they are strongly chemisorbed on the NiMoPR due to covalent bonding. Weakly adsorbed BPE allows higher mobility during diffusion to the catalytic site, which promotes the higher activity of NiMoPS for the HDL. This work demonstrates the potential use of clay-supported NiMo catalysts for lignin valorization and the future circular economy.
4 June 2024 in Bulletin of Chemical Reaction Engineering & Catalysis
The potential of bentonite as a catalyst is rapidly growing, isomorphic substitution in its interlayer allows for cation exchange and facilitates modification to enhance its catalytic properties. The catalytic performance of bentonite can be improved through the insertion of pillared clays (PILC) into its interlayer structure using Al2O3, NiO, and MnO metal oxide alloys. This research aims to develop and study a modified bentonite catalyst, focusing on its physicochemical changes,as well as its activity and selectivity in the conversion of ethanol to biogasoline. The synthesis of oxide pillars on bentonite was carried out at a consistent metal/bentonite mole ratio of 10 mmol/g, with a mixed metal composition of 1:1. The results showed anexpansion of interlayer distance, as measured by X-ray diffraction (XRD), which increased in all catalysts compared to natural bentonite6,350 (13.94 Å). Surface Area Analyzer (SAA) analysis, revealed that Al/Bentonite exhibited the highest surface area at187.84 m2/g. Total acidity analyzed, using Temperature Programmed Desorption-Ammonia (TPD-NH3), was found to be 2.33 mmol/g, with Al-Ni/Bentonite showing the highest acidity. Thermal stability, tested throughThermogravimetric Analysis (TGA), indicated that catalysts containing Al and Ni demonstrated the highest stability. The catalytic activity test showed that the Al/bentonite catalyst achieved the highest ethanol conversion rate of68.64% and a catalyst selectivity of 51.70%, as determined byGas Chromatography-Flame Ionized Detector (GC-FID) analysis. These results indicate that the pillarization of bentonite with Al2O3, NiO, and MnO oxides significantly improved its physicochemical properties, activity, and selectivity in the catalytic conversion of ethanol to biogasoline compared to natural bentonite.