Synthesis of SnO2–Fe3O4 nanocomposites was conducted. The purpose of this study was to obtain the SnO2–Fe3O4 nanocomposites, the effectiveness of photodegradation Congo red by SnO2–Fe3O4 nanocomposites and determine the kinetics of photodegradation. The XRD analysis showed that the SnO2–Fe3O4 nanocomposite best mass ratio was 1:1 based on the highest intensity of characteristic angle (2θ), which is 26.54° and had the smallest crystal size, which is 9.662 nm. Based on the UV-Vis DRS result, the SnO2–Fe3O4 nanocomposites bandgap value was 2.3 eV. The magnetization saturation value of SnO2–Fe3O4 nanocomposites was 64.96 emu/g. The morphology of SnO2–Fe3O4 nanocomposites showed by the TEM image, where the dark spots spread in the lighter areas. The surface of SnO2–Fe3O4 nanocomposites characterized by SEM with the result was bumpy surface and many pores. The EDS result of SnO2–Fe3O4 nanocomposites confirmed the presence of Fe, Sn, and O elements. The functional group of SnO2–Fe3O4 nanocomposites showed by FTIR data, the stretch band of Sn–O characteristics showed at wavenumber 590 cm−1, and the stretch band of Fe–O showed at wavenumber 563 cm−1. The optimum condition of nanocomposites at a contact time of 90 min and the optimum concentration of 18 mg/L showed that the percent of photodegradation was 50.76%. The photodegradation rate of SnO2–Fe3O4 was fitted to Pseudo-second-order.
In this study, bentonite modified by zirconium nitride (ZrN) and zirconium phosphide (ZrP) catalysts was studied in the hydrocracking of crude palm oil to biofuels. The study demonstrated that bentonite was propitiously modified by ZrN and ZrP, as assessed by XRD, FTIR spectroscopy, and SEM-EDX analysis. The acidity of the bentonite catalyst was remarkably enhanced by ZrN and ZrP, and it showed an increased intensity in the Lewis acid and Brønsted acid sites, as presented by pyridine FTIR. In the hydrocracking application, the highest conversion was achieved by bentonite-ZrN at 8 mEq g−1 catalyst loading of 87.93%, whereas bentonite-ZrP at 10 mEq g−1 showed 86.04% conversion, which suggested that there was a strong positive correlation between the catalyst acidity and the conversion under a particular condition. The biofuel distribution fraction showed that both the catalysts produced a high bio-kerosene fraction, followed by bio-gasoline and oil fuel fractions. The reusability study revealed that both the catalysts had sufficient conversion stability of CPO through the hydrocracking reaction up to four consecutive runs with a low decrease in the catalyst activity. Overall, bentonite-ZrN dominantly favored the hydrocracking of CPO than bentonite-ZrP.
In this study, molybdenum nitride-bentonite was successfully employed for the reaction of hydrocracking of palm oil to produce a bio-gasoline and bio-aviation fuel. The prepared catalyst was characterized using XRD, FT-IR, and SEM-EDX. The acidity of the catalyst was determined using the pyridine gravimetric method. The result showed that the acidity of bentonite was increased after modification using molybdenum nitride. The hydrocracking study showed that the highest conversion and product fraction of bio-gasoline and bio-aviation fuel were exhibited by molybdenum nitride-bentonite 8 mEq g−1. The catalyst was later used to optimize the hydrocracking process using RSM-CCD. The effects of the process variables such as temperature, contact time, and catalyst to feed ratio, on the response variables, such as conversion, oil, gas, and coke yield, were investigated. The analysis of variance showed that the proposed quadratic model was statistically significant with adequate precision to estimate the responses. The optimum conditions in the hydrocracking process were achieved at a temperature of 731.94 K, contact time of 0.12 h, and a catalyst to feed ratio of 0.12 w/v with a conversion of 78.33%, an oil yield of 50.32%, gas yield of 44.00% and coke yield of 5.73%. The RSM-CCD was demonstrated as a suitable method for estimating the hydrocracking process of palm oil using a MoN-bentonite catalyst due to its closeness to the optimal value of the expected yield. This study provided a potential catalyst of based on bentonite modified using molybdenum nitride for the hydrocracking of palm oil.
Zr-containing SiO2 and their parent catalysts were fabricated with different methods using EDTA chelation and template-assist. The activity of the catalysts was explored in crude palm oil (CPO) hydrocracking, conducted under a continuous system micro-cylindrical reactor. The conversion features and the selectivity towards biofuel products were also examined. The physicochemical of catalysts, such as structure phase, functional groups, surface morphologies, acidity features, and particle size, were investigated. The study showed that the template method promoted the crystalline porous catalysts, whereas the chelate method initiated the non-porous structure. The catalysts’ acidity features of SiO2 and SiO2/Zr were affected by the preparation, which revealed that the EDTA chelate-assisted method provided higher acidity features compared with the template method. The CPO hydrocracking study showed that the SiO2/Zr-CEDTA provided the highest catalytic activity towards the hydrocracking process, with 87.37% of conversion attained with 66.29%.wt of liquid product. This catalyst exhibited selectivity towards bio-jet (36.88%), bio-diesel (31.43%), and bio-gasoline (26.80%). The reusability study revealed that the SiO2/Zr-CEDTA had better stability towards CPO conversion compared with SiO2/Zr-CEDTA, with a low decrease in catalyst performance at three consecutive runs.
7 October 2025 in Bulletin of Chemical Reaction Engineering & Catalysis
Coconut oil mill waste (CMW) contained high free fatty acid (FFA) content which potentially could be converted into a value-added product such as fatty acid methyl ester (FAME). In this study, a montmorillonite-sulfonated carbon catalyst was used to evaluate the kinetic parameter of FFA conversion from CMW into FAME. The characterization of FTIR and SEM-EDX confirmed that the -SO3H groups were successfully incorporated into montmorillonite- carbon catalyst. The highest catalyst acidity (9.4 mmol/g) was achieved by a ratio of montmorillonite to sulfonated carbon of 1:3 % w/w. The kinetic study using montmorillonite-sulfonated carbon 1:3 % w/w showed that the reaction temperature and molar ratio of methanol to FFA (% v/v) were positively correlated to the reaction rate. The highest rate constant of esterification towards the product (k1), reactant (k2), and equilibrium were 0.1187, 0.0595, and 1.995, achieved by a temperature of 80 ˚C, respectively. The Arrhenius constant and activation energy towards the product were 3.3085×106 and 50.3 J/mole, respectively. The reaction temperature was positively correlated to the equilibrium constant, which indicated that the reaction was endothermic. The kinetic model validation revealed that the predicted value from the model was adequately in accordance with the experimental value, as indicated by a high coefficient of determination.