In this study, bentonite modified by zirconium nitride (ZrN) and zirconium phosphide (ZrP) catalysts was studied in the hydrocracking of crude palm oil to biofuels. The study demonstrated that bentonite was propitiously modified by ZrN and ZrP, as assessed by XRD, FTIR spectroscopy, and SEM-EDX analysis. The acidity of the bentonite catalyst was remarkably enhanced by ZrN and ZrP, and it showed an increased intensity in the Lewis acid and Brønsted acid sites, as presented by pyridine FTIR. In the hydrocracking application, the highest conversion was achieved by bentonite-ZrN at 8 mEq g−1 catalyst loading of 87.93%, whereas bentonite-ZrP at 10 mEq g−1 showed 86.04% conversion, which suggested that there was a strong positive correlation between the catalyst acidity and the conversion under a particular condition. The biofuel distribution fraction showed that both the catalysts produced a high bio-kerosene fraction, followed by bio-gasoline and oil fuel fractions. The reusability study revealed that both the catalysts had sufficient conversion stability of CPO through the hydrocracking reaction up to four consecutive runs with a low decrease in the catalyst activity. Overall, bentonite-ZrN dominantly favored the hydrocracking of CPO than bentonite-ZrP.
In this study, molybdenum nitride-bentonite was successfully employed for the reaction of hydrocracking of palm oil to produce a bio-gasoline and bio-aviation fuel. The prepared catalyst was characterized using XRD, FT-IR, and SEM-EDX. The acidity of the catalyst was determined using the pyridine gravimetric method. The result showed that the acidity of bentonite was increased after modification using molybdenum nitride. The hydrocracking study showed that the highest conversion and product fraction of bio-gasoline and bio-aviation fuel were exhibited by molybdenum nitride-bentonite 8 mEq g−1. The catalyst was later used to optimize the hydrocracking process using RSM-CCD. The effects of the process variables such as temperature, contact time, and catalyst to feed ratio, on the response variables, such as conversion, oil, gas, and coke yield, were investigated. The analysis of variance showed that the proposed quadratic model was statistically significant with adequate precision to estimate the responses. The optimum conditions in the hydrocracking process were achieved at a temperature of 731.94 K, contact time of 0.12 h, and a catalyst to feed ratio of 0.12 w/v with a conversion of 78.33%, an oil yield of 50.32%, gas yield of 44.00% and coke yield of 5.73%. The RSM-CCD was demonstrated as a suitable method for estimating the hydrocracking process of palm oil using a MoN-bentonite catalyst due to its closeness to the optimal value of the expected yield. This study provided a potential catalyst of based on bentonite modified using molybdenum nitride for the hydrocracking of palm oil.
The rice husk has the potential to be used for converting agricultural wastes into renewable energy. Therefore, this study aims to improve the hydrolysis of rice husk through Hydrogen Peroxide (HP) and Combined Hydrogen Peroxide–Aqueous Ammonia (CHPA) pretreatments. The removal of lignin from rice husks was determined using SEM–EDS examination of the samples. At a specific concentration of H2O2, (CHPA) pretreatment eliminated a significantly larger amount of lignin from biomass. The percentage of lignin removal of HP varied from 48.25 to 66.50, while CHPA ranged from 72.22 to 85.73. Hence, the use of batch kinetics of lignin removal of both pretreatments is recommended, where the kinetic parameters are determined by fitting the experimental data. Based on the results, the activation energies for HP and CHPA pretreatments were 9.96 and 7.44 kJ/mol, which showed that the24 model is appropriate for the experimental data. The increase in temperatures also led to a higher pretreatment value, indicating their positive correlation. Meanwhile, CHPA pretreatment was subjected to enzymatic hydrolysis of 6% enzyme loading for the production of 6.58 g glucose/L at 25 h.
In this preliminary research, the catalytic activity of isopropyl alcohol conversion to diisopropyl ether through dehydration reaction catalyzed by zeolite-Ni and zeolite-Ni(H2PO4)2 was comparatively described. The natural zeolite was treated with 1% HF and 6 N HCl prior to modifications using the impregnation method. Isopropyl alcohol conversion was examined at a mild temperature of 150 °C for 3.5 h on the reflux system with various catalyst loadings. X-ray diffraction and Fourier transform infrared analysis confirmed the successful impregnation of nickel and nickel phosphate into the zeolite. Scanning electron microscopy analysis revealed a cubic-like structure on zeolite-Ni(H2PO4)2, whereas homogenously distributed nickel species were observed on the zeolite-Ni catalyst. Energy-dispersive X-ray spectroscopy analysis reinforced the accomplishment of zeolite modifications. The N2 physisorption isotherms showed a decline in the surface area and total pore volume of the zeolite because of the blocking of pores. The zeolite-Ni(H2PO4)2 catalyst had higher acidity than unmodified zeolite and zeolite-Ni catalysts, which inherently suggested that the presence of phosphate groups results in higher catalytic activity toward isopropyl alcohol. The highest catalytic activity was attained by 8 mEq/g metal loading zeolite-Ni(H2PO4)2 with isopropyl alcohol conversion of 81.51%, diisopropyl ether yield, and selectivity of 40.77 and 33.16%. The reusability study suggested that the zeolite-Ni(H2PO4)2 catalyst was still active and had sufficient catalytic activity stability toward isopropyl alcohol after the third cycle was reused. This nickel phosphate-based modified zeolite was adequately potential for diisopropyl ether production through isopropyl alcohol dehydration.
In this study, the catalytic activity of bifunctionalSiO(2)/Zr catalysts prepared by template and chelate methodsusing potassiumhydrogen phthalate (KHF) for crude palm oil (CPO) hydrocracking tobiofuels was investigated. The parent catalyst was successfully preparedby the sol-gel method, followed by the impregnation of zirconiumusing ZrOCl2 center dot 8H(2)O as a precursor. The morphological,structural, and textural properties of the catalysts were examinedusing several techniques, including electron microscopy energy-dispersiveX-ray with mapping, transmission electron microscopy, X-ray diffraction,particle size analyzer (PSA), N-2 adsorption-desorption,Fourier transform infrared-pyridine, and total and surface acidityanalysis using the gravimetric method. The results showed that thephysicochemical properties of SiO2/Zr were affected bydifferent preparation methods. The template method assisted by KHF(SiO2/Zr-KHF2 and SiO2-KHF catalysts) providesa porous structure and high catalyst acidity. The catalyst preparedby the chelate method assisted by KHF (SiO2/Zr-KHF1) exhibitedexcellent Zr dispersion toward the SiO2 surface. The modificationremarkably enhanced the catalytic activity of the parent catalystin the order SiO2/Zr-KHF2 > SiO2/Zr-KHF1> SiO2/Zr > SiO2-KHF > SiO2, with sufficientCPO conversion. The modified catalysts also suppressed coke formationand resulted in a high liquid yield. The catalyst features of SiO2/Zr-KHF1 promoted high-selectivity biofuel toward biogasoline,whereas SiO2/Zr-KHF2 led to an increase in the selectivitytoward biojet. Reusability studies showed that the prepared catalystswere adequately stable over three consecutive runs for CPO conversion.Overall, SiO2/Zr prepared by the template method assistedby KHF was chosen as the most prominent catalyst for CPO hydrocracking.
Zr-containing SiO2 and their parent catalysts were fabricated with different methods using EDTA chelation and template-assist. The activity of the catalysts was explored in crude palm oil (CPO) hydrocracking, conducted under a continuous system micro-cylindrical reactor. The conversion features and the selectivity towards biofuel products were also examined. The physicochemical of catalysts, such as structure phase, functional groups, surface morphologies, acidity features, and particle size, were investigated. The study showed that the template method promoted the crystalline porous catalysts, whereas the chelate method initiated the non-porous structure. The catalysts’ acidity features of SiO2 and SiO2/Zr were affected by the preparation, which revealed that the EDTA chelate-assisted method provided higher acidity features compared with the template method. The CPO hydrocracking study showed that the SiO2/Zr-CEDTA provided the highest catalytic activity towards the hydrocracking process, with 87.37% of conversion attained with 66.29%.wt of liquid product. This catalyst exhibited selectivity towards bio-jet (36.88%), bio-diesel (31.43%), and bio-gasoline (26.80%). The reusability study revealed that the SiO2/Zr-CEDTA had better stability towards CPO conversion compared with SiO2/Zr-CEDTA, with a low decrease in catalyst performance at three consecutive runs.