For this data article the adsorption of Basic Blue 41 (BB 41) dye by activated carbon derived from filamentous algae (AAC) of available in agriculture waste as cheap adsorbents were examined. Activated carbon has been widely used as an adsorbent regard to its massive specific surface area, high porosity, reusability and thermal stability for the removal of pollutants from effluent. These filamentous algae grow widely in irrigation streams, causing decreasing speed of water flow and are not even eaten by livestock so are considered agricultural wastes. They can be used as precursors for activated carbon preparation and as adsorbent for the dye removal. The data of initial dye concentration (50-200 mg//L), pH of dye solution (3-9), adsorbent dosage (0.25-2 g/L), and contact time (5-200 min), were assessed. The structure of AAC was characterized by X-ray diffraction and Fourier transforms infrared spectroscopy. Activated carbon with a 94% removal of dye at concentration of 100 mg/L, pH 9, and adsorbent dose 1 g/L after 90 min. The data of isotherms and Kinetics indicated that the experimental data are fitted to Langmuir and second-pseudo-order models. Under the optimum conditions, maximum adsorption capacity of the AAC in Langmuir model enhanced to amount of 125 mg/g. According to the experimental data, filamentous algae are a suitable raw material for activated carbon production.
13 April 2020 in International Journal of Environmental Analytical Chemistry
Huge quantities of different dyes are generated by various industries such as cosmetic, leather, printing and textile and food. This study aimed to generate and apply tire-derived activated carbon magnetised with the Fe3O4 nanoparticles (MAC) for the removal of reactive blue 19 (RB19) dye from aquatic solutions. FE-SEM, VSM, XRD, FTIR and BET analyses were used to determine MAC properties. Under optimal conditions of pH 3, the initial concentration of dye 100 mg/L, the composite dose 1 g/L and the reaction time of 45 min, the removal efficiency for RB19 was 93.22%. Isotherm findings illustrated that RB19 adsorption onto the MAC followed the Langmuir model. Moreover, the absorption kinetics is well interpreted by the pseudo-second-order model in low scrutinised concentrations. The SBET and total pure volume for the MAC were 421.11 m2 g−1 and 0.467 cm3 g−1. Under the optimum conditions, maximum adsorption capacity of the MAC in Langmuir model enhanced to the amount of 119.05 mg/g. Also, the reusability (with NaOH) of the MAC revealed about 21% decreases in the removal efficiency within five consecutive runs. It is concluded that the application of the magnetised activated carbon due to its high efficiency in removing RB19 from laboratory and actual samples can be evaluated in future studies to be utilised in real scales.
12 December 2020 in Separation Science and Technology
Drainage of untreated wastewater from the textile industry due to the use of toxic compounds in it causes pollution in aquatic environments and major environmental and health problems. Therefore, the aim of the present study is to compare the performance of activated carbon coated with AC-ZnO composite as an adsorbent to remove the AB-113 from the aqueous solution. The present study is an experimental-laboratory study in which the effect of independent parameters has been investigated. FTIR and XRD analyzes were performed to determine the composition of the composite. Isothermal and kinetic adsorption at different concentrations were evaluated to evaluate the process. The results of physical-chemical analysis confirmed the correctness of the composite structure. Optimal conditions for AB-113 (with a concentration of 100 mg/L, a composite dose of 0.5 g/L, a reaction time of 15 minutes and pH = 3) 98.2% were obtained. The results of the study of isothermal and kinetic adsorption for dye showed that the adsorption process follows the isotherm of Freundlich (R2 = 0.9859) and Pseudo-second-order. The maximum adsorption capacity of AC-ZnO composite was determined using Langmuir model 333.33 mg/g. Thermodynamic parameters showed the non-spontaneity and endothermic in nature of adsorption process. The present study showed that nanoparticle stabilization technology can be used on activated carbon as an effective and efficient adsorbent to remove dye from aqueous solutions.
Cephalexin is extensively used as an antibiotic for treatment a number of bacterial infections. The data of possible adsorption mechanism and isotherm of Cephalexin on the synthesized adsorbent are depicted in this data article. The data obtained showed that the adsorption trend follows the pseudo-second order kinetic model and that the Langmuir isotherm was suitable for correlation of equilibrium data with the maximum adsorption capacity of 48.78 mg/g. Considering the findings data, powdered activated carbon derived from pomegranate peel as available and a cheap adsorbent, could be considered as promising adsorbent for Cephalexin and probably similar organic pollutants removal from aqueous solutions.
The natural organic matter in water resources poses many problems, such as unpleasant taste and colour in the water, and is one of the most important precursors to the formation of disinfection byproducts (DBPs) during water treatment. This study was performed to evaluate the efficiency of activated carbon (AC) and activated carbon coated with nZVI nanoparticles (AC-nZVI) to remove humic acid from aqueous solutions. To end this, the effect of some operational factors including pH, contact time, humic acid concentration and adsorbent dose was studied in removal of humic acid from aqueous solutions in the presence of AC and AC-nZVI. The structure of the adsorbents and their morphology were characterized by FTIR, BET, SEM and XRD analyzes. The adsorption isotherm was determined using Langmuir, Freundlich and kinetic adsorption models by studying quasi-first-order and quasi-second-order models. The thermodynamic parameters of the adsorption system such as changes in enthalpy (ΔH0), entropy (ΔS0) and free energy of Gibbs (ΔG0) were also measured and evaluated. The results showed that the removal efficiency is directly associated with the dose of adsorbent and has a reverse association with pH and humic acid concentration. The optimal removal of humic acid at the adsorbent dosage of 1.6 g/L, the humic acid concentration of 50 mg/L and the contact time of 45 min was found 84.7% and 95.68% for AC and AC-nZVI, respectively. The SBET and total pure volume for the AC-nZVI were 821.52 m2/g and 0.631 cm3/g respectively. The removal rate by AC-nZVI as significantly high, indicating the effective role of nanoparticle stabilisation on activated carbon. As a result, it is possible to find an effective and highly efficient adsorbent by stabilising the nanoparticles on activated carbon that can be used to remove humic acid.