The structural parameters of the liquid sheet represent a significant factor influencing the atomization performance, and its measurement is an important part of the agrochemical atomization study. Currently, the measurement predominantly relies on commercial software with manual operation, which is labor intensive and inefficient. In this study, deep learning methods with high-speed photographing were employed to measure the structural parameters of the liquid sheet of hydraulic nozzles with different atomization modes. The LM-YOLO liquid sheet structure recognition model was constructed to recognize the liquid sheet and perforations. Based on the recognition results, a method is designed to calculate several key parameters, including the breakup length, the liquid sheet area, the spray angle, the average number of perforations, and the average perforation area. A comparative scrutiny of the assorted liquid sheet structural parameters under different experimental conditions was also implemented. Based on the constructed model, a recognition accuracy of 81.0% for the liquid sheet structure of the LU nozzle (a classical hydraulic nozzle with high liquid sheet integrity) and 71.3% for the IDK nozzle (an air-induced hydraulic nozzle with a certain amount of bubbles in the liquid sheet) was achieved. The liquid sheet structure was measured based on the recognition results. It was found that the pressure has a significant impact on the structural parameters of the liquid film. For the LU120-03 nozzle, the breakup length of the liquid film decreases from 48.96 mm to 39.05 mm as the pressure increases. In contrast, for the IDK120-03 nozzle, the breakup length exhibits fluctuating changes, with a peak value of 29.65 mm occurring at 250 kPa. After adding silicone adjuvant, the breakup length and area of the liquid film generally decrease. The variation trends of the measured structural parameters under different experimental conditions are consistent with the trends of the data in previous relevant research by other scholars. This study provides a new method for measuring out the structural parameters of the liquid sheet, and it has potential application in related fields.
Spraying drift is a key concern in aerial spraying and relates closely to droplet size. With the growing application of large-load UAVs, large-load plant protection UAVs lack corresponding spraying devices. The rotary cage atomizer, suitable for high-flow aerial spraying, is a better option for large-load plant protection UAVs’ spraying needs. A modified rotating cage atomizer based on the AU5000 atomizer in manned aircraft was designed, with cage diameters of 76 mm, 86 mm, 96 mm, 106 mm, and 116 mm. Based on the IEA-I high-speed wind tunnel, this study investigated the impacts of different wind speeds, flow rates, and cage diameters on the atomization characteristic distribution of the modified atomizer and established a model. The results show that when other variables remain constant, for every 1 mm increase in cage diameter, the average droplet size decreases by 0.944 μm. The R2 of the predicted values and the measured values of the droplet size model is 0.917. Under the conditions of 50 m/s, 58.3 m/s, and 66.6 m/s wind speeds, as the cage diameter increases, Relative Span (RS) shows a trend of first increasing and then decreasing. Among them, the RS of the 106 mm cage diameter is usually the highest. This study can provide a reference for the aerial spraying scheme of large-payload plant protection UAVs, such as the selection of the diameter of the rotating cage.
(1) Background: Various types of adjuvants are added during application to enhance the spraying effect, but most adjuvant formulations are proprietary products, and their exact compositions have not been disclosed. (2) Methods: The spatial distributions of droplet sizes and velocities generated by the atomization of different polymer adjuvants were measured based on the phase Doppler interferometer (PDI) measurement method. The sub-area statistical method was used to quantitatively analyze the droplet characteristics at various points below the nozzle. (3) Results: The polymer (polyethylene oxide (PEO))/associative surfactant (sodium dodecyl sulfate (SDS)) can increase the droplet size and velocity of the solution after atomization by increasing the amount of the polymer/associative surfactant to reduce the equilibrium surface tension of the solution and increase the viscosity. Different concentrations of polymer/associative surfactant atomization produced larger droplet sizes and better uniformity than polymer/non-associative surfactant (polysorbate-20 (Tween20)). At the same position, the relationship between droplet velocities for the three adjuvant combinations was roughly as follows: PEO/SDS solution had the highest velocity, followed by PEO solution, and PEO/Tween20 solution had the lowest velocity. (4) Conclusions: The optimal of droplet size distribution can be achieved by adding appropriate amounts of associative surfactants to polymers.
1 January 2025 in International Journal of Agricultural and Biological Engineering