This article proposes a quad-core millimeter-wave (mm-wave) voltage-controlled oscillator (VCO) using a compact multi-mode magnetically coupled LC network. The network can be configured to achieve four different resonant modes. In conjunction with the mode switches, four VCO cores are coupled with each other to achieve the quad-mode switching; thus, the tuning range (TR) is widened. In addition, the mismatch and phase noise (PN) of the asymmetrical multi-core oscillator have been analyzed. Implemented in 65-nm CMOS process, the VCO achieves a measured continuous TR of 90.2%, from 12.1 to 32.0 GHz. The measured best PN is $-$ 103.2 dBc/Hz at 13.2 GHz with 1-MHz offset, corresponding to a figure-of-merit (FoM) of $-$ 177.6 dBc/Hz and an FOM of TR and area (FoM $_{\mathrm{TA}}$ ) of $-$ 207.7 dBc/Hz. This chip operates at a 0.8-V supply with a power consumption of 5.6–22.5 mW and a core area of 0.08 mm $^{2}$ . $^{^{^{^{}}}}$
21 June 2024 in IEEE Microwave and Wireless Technology Letters
A millimeter-wave CMOS active vector-sum phase shifter (VSPS) with a phase resolution of 5.625 $^{\circ}$ using a two-stage transformer-based resistor and inductor (RL) polyphase filter (PPF) for generating wideband in-phase/quadrature (I/Q) signals is proposed. Theoretical analysis demonstrates that the inductors in RL PPF can resonate with the capacitive loads to boost the passive voltage gain and alleviate the issue of high loss in the traditional RC PPF. Furthermore, the RL PPF provides a larger bandwidth and a better tolerance to process variations. An active VSPS prototype incorporating the proposed RL PPF is implemented in 65-nm CMOS process. The measured results of the phase shifter show a maximum insertion gain of $-$ 2.28 dB with a maximum power consumption of 20.52 mW. The measured root-mean-square (rms) phase error and gain error over the 360 $^{\circ}$ phase shifting range are 0.71 $^{\circ}$ –2.95 $^{\circ}$ and 0.67–0.76 dB, respectively, from 20 to 30 GHz (FBW $=$ 40%). The core size is 0.238 mm $^{2}$ .
27 February 2025 in IEEE Transactions on Microwave Theory and Techniques
This article presents a dual-mode, dual-band power amplifier (PA) capable of covering both the fifth-generation (5G) FR1 and FR2 bands for 5G user equipment driver applications. The common-mode (CM) path, often overlooked in a typical differential-mode (DM) CMOS PA, is analyzed and utilized as an alternative path to cover a second frequency band. A universal topology is proposed for the utilization of both DM and CM in PA and other RF circuits. By assigning the millimeter-wave (mm-Wave) and sub-7 GHz bands to DM and CM paths, respectively, this PA achieves coverage of both 3.5 and 27 GHz bands with only one amplifying stage and consequently a compact layout. On the DM path, the proposed PA achieves a P1 dB and PAE1 dB of 18.1 dBm and 32.4% at 24 GHz, while on the CM path, the corresponding performance is 15.3 dBm and 35.5% at 3.7 GHz. The proposed PA exhibits an adjacent channel leakage ratio (ACLR) of -25.9 dBc, an average power-added efficiency (PAE) of 17%, and an average output power of 12.4 dBm at -24.7 dB EVMRMS with a 64 QAM 200 MSym/s modulation signal at 26 GHz in DM. Similarly, with 256 QAM 50 MSym/s modulation at 3.6 GHz in CM, the PA demonstrates -35.6 dBc ACLR, 22.5% average PAE, and 10.7 dBm average power at -31.1 dB EVMRMS. Furthermore, measurements with two carriers at 24 and 3.7 GHz indicate that the PA has the potential for concurrent operation in both modes. The PA is fabricated in a 65 nm CMOS process with a core area of 0.32 mm2.
5 November 2024 in IEEE Transactions on Microwave Theory and Techniques
A novel wideband $I/Q$ network with multiple phase error zeros (MPEZs) is proposed and adopted in a millimeter-wave (mmW) mixer design for high image rejection. The single-ended (SE) MPEZs $I/Q$ network combines topologies of low-pass network and bandpass network. Compared to the conventional $I/Q$ network, our design introduces an inductor $L_{{C}}$ in the bandpass network ( $I$ -path) to improve the bandwidth by generating a new phase error zero. Meanwhile, a capacitor $C_{{C}}$ is inserted in the low-pass network ( $Q$ -path) to assist in optimizing the quadrature performance. Furthermore, a differential form of MPEZs $I/Q$ network is constructed and further improves the bandwidth and amplitude errors. In the differential structure, $L_{{C}}$ can make the voltage gain of $I$ -and $Q$ -paths close to each other to reduce the amplitude error. $C_{{C}}$ primarily affects the voltage gain of the $Q$ -path but has little impact on the voltage gain of the $I$ -path which can accommodate to slightly optimize the amplitude error. A mmW image rejection mixer (IRM) using the proposed differential $I/Q$ network was implemented by the TSMC 65 nm CMOS process. The mixer achieves a measured image-rejection ratio (IRR) higher than 40 dB within a bandwidth from 23.5 to 29.5 GHz (22.6%). It also shows a measured conversion gain (CG) of about 15.5 dB under 5 dBm local oscillator (LO) power, IP1 dB around $-$ 20 dBm, and the IIP3 from $-$ 14.2 to $-$ 12.8 dBm. The power consumption of the mixer with all buffers is 108 mW and the whole chip occupies 0.525 mm $^{{2}}$ .
20 January 2025 in IEEE Transactions on Circuits and Systems II: Express Briefs
In this brief, an inductor-less low-noise amplifier (LNA) that utilizes a noise-canceling technique along with dual-resistor feedback is proposed. The conventional single-resistor feedback structure exhibits a performance constraint that limits the relationship between power gain and input matching. In contrast, the dual-resistor feedback structure proposed in this brief overcomes this limitation, enabling both high gain and low noise while maintaining good input matching. The dual-resistor feedback configuration includes a local feedback resistor which enhances the gain. Additionally, the global feedback resistor directly connect the inputs and outputs of the circuit, thereby breaking the constraints between the properties through feedback. The proposed LNA fabricated in 65-nm CMOS technology exhibiting a minimal NF of 2.08 dB within a 3-dB bandwidth that spans from 0.25 to 2.83 GHz, along with a peak power gain of 16.53 dB. The circuit operates with a power consumption of 10.6 mW under a supply voltage of 1.1 V, while occupying a core area of only 0.012 mm2.
12 February 2025 in IEEE Transactions on Circuits and Systems II: Express Briefs
This paper presents a D-band power amplifier (PA) with high output power and high back-off efficiency in 40nm GP CMOS technology. The PA is based on a four-way parallel power-combining Doherty architecture. Two sub-amplifiers with high output power have been realized using a highly balanced impedance-transforming power combiner based on the SLOT-GCPW structure. A transmission-line-like impedance inverter and a quadrature coupler with a slow wave coplanar waveguides (S-CPWs) are proposed to obtain compact size. Meanwhile, the adaptive bias technique is used to overcome the difficulties of implementing conventional Doherty architectures at terahertz (THz). The measured Doherty PA realizes a peak small-signal gain of 15.3 dB with 17 GHz 3-dB bandwidth. At 140 GHz, the PA achieves 16.1 dBm saturated output power (Psat) with peak power-added-efficiency (PAE) of 7% and 3% PAE at 6-dB power back-off (PBO) from Psat. To the authors’ best knowledge, this is the first D-band CMOS integrated PA with high PBO efficiency.