Grigoris Kaltsas

Prof. Grigoris Kaltsas

Department of Electrical and Electronics Engineering, University of West Attica, GR-12210 Egaleo, Athens, Greece
orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 January 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Dimitris BarmpakosDimitris Barmpakos
Dimitris Barmpakos
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas
Printing technologies have been attracting increasing interest in the manufacture of electronic devices and sensors. They offer a unique set of advantages such as additive material deposition and low to no material waste, digitally-controlled design and printing, elimination of multiple steps for device manufacturing, wide material compatibility and large scale production to name but a few. Some of the most popular and interesting sensors are relative humidity, temperature and strain sensors. In that regard, this review analyzes the utilization and involvement of printing technologies for full or partial sensor manufacturing; production methods, material selection, sensing mechanisms and performance comparison are presented for each category, while grouping of sensor sub-categories is performed in all applicable cases. A key aim of this review is to provide a reference for sensor designers regarding all the aforementioned parameters, by highlighting strengths and weaknesses for different approaches in printed humidity, temperature and strain sensor manufacturing with printing technologies.

1 March 2020 in Microelectronic Engineering
Verified
Journal Article
Closed access
Dimitris BarmpakosDimitris Barmpakos
Dimitris Barmpakos
CTChristos Tsamis
Christos Tsamis
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas

1 October 2002 in IEEE Sensors Journal
Verified
Journal Article
Closed access
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas
ANA.A. Nassiopoulos
A.A. Nassiopoulos
ANA.G. Nassiopoulou
A.G. Nassiopoulou
In this paper, the results of full characterization of a micromachined-silicon thermal gas flow sensor will be presented. The sensor is composed of two series of thermocouples on the right and left side of a polysilicon resistor, used as heater. The resistor and the hot contacts of the thermocouples lie on a thick porous silicon layer, which assures local thermal isolation, while the thermopile cold contacts lie on bulk silicon. Gas flow is parallel to the surface of the sensor and perpendicular to the resistor, which is heated at constant temperature. The power of the heater is stabilized by an external circuit, which provides a feedback current to compensate changes in the resistance of the heater under flow. Characterization of the sensor both under static conditions and under flow of different gases will be presented. The sensor shows high sensitivity [of the order of 175 /spl times/ 10/sup -3/ mV/(m/s)/sup 1/2/ per thermocouple] and very rapid response, below 1 ms, which makes it appropriate for use both under laminar and under turbulent flows.

Verified
Journal Article
Open access
PDF file
APAggelos Pilatis
Aggelos Pilatis
Dimitrios - Nikolaos PagonisDimitrios - Nikolaos Pagonis
Dimitrios - Nikolaos Pagonis
MSMichael Serris
Michael Serris
SPSofia Peppa
Sofia Peppa
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas
In this work, over a thousand maritime casualty reports were reviewed in order to fully investigate and assess selected 213 marine accidents concerning the collision, grounding, and hull failure of ships, which occurred during the time period of 1990–2020, worldwide. Ship type and vessels’ main characteristics, as well as the cause of accidents, were categorized and analyzed statistically. The statistical software IBM SPSS© Statistics v.29 was employed for the investigation of a possible association between the above set criteria. Furthermore, the location and the extent of hull damage was extracted for all incidents, providing valuable insights into the resulting consequences for vessel integrity. These data are essential for estimating the accident’s impact on the viability of the ship, crew, and cargo. According to the main results obtained, significant correlations are deduced regarding the analyzed parameters. In collision accidents, these include the ship type, the location of the damage, visibility and age of the ship, the impact of the accident, and the type of casualty. In the case of grounding incidents, correlations emerge involving the type of ships, day/night period, the width of the resulting damage, the type of casualty, and the cause of accidents.

1 February 2008 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
DRDanijela Randjelović
Danijela Randjelović
APAnastasios Petropoulos
Anastasios Petropoulos
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas
MSMiloš Stojanović
Miloš Stojanović
ŽLŽarko Lazić
Žarko Lazić
MMMilan Matić
Milan Matić

30 June 2009 in Microelectronic Engineering
Verified
Journal Article
Closed access
KKKonstatinos Kontakis
Konstatinos Kontakis
APAnastasios Petropoulos
Anastasios Petropoulos
Grigoris KaltsasGrigoris Kaltsas
Grigoris Kaltsas
TSThanassis Speliotis
Thanassis Speliotis
Evangelos GogolidesEvangelos Gogolides
Evangelos Gogolides