Kyoung-Min Choo

Mr. Kyoung-Min Choo

Sungkyunkwan University
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 May 2020 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
KCKyoung-Min Choo
Kyoung-Min Choo
CWChung-Yuen Won
Chung-Yuen Won
In this paper, an electrical braking torque limit trajectory is designed to improve the regenerative braking of electric vehicles based on a regenerative power analysis. Even though electric motors generally regenerate electric energy from kinetic energy, the drive system dissipates electric energy under certain low-speed operation conditions. This phenomenon has been addressed in many previous works and most of them compensate for this power dissipation region by modifying the electrical braking torque limit trajectory of the motor. However, the torque limit trajectory has never been considered based on a regenerative power analysis even though an inaccurate torque limit trajectory causes energy loss to the drive system. In this paper, the regenerative power analysis for two major kinds of permanent magnet synchronous motor is performed. Afterward, torque limit trajectories are set based on this analysis so that batteries in electric vehicles can harvest the maximum regenerative energy in any circumstance. To verify the analysis and proposed torque limit trajectories, simulations and experiments are performed.

2 September 2020 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
KCKyoung-Min Choo
Kyoung-Min Choo
CWChung-Yuen Won
Chung-Yuen Won
In this article, a flying start method for sensorless-controlled permanent-magnet-synchronous-machine (PMSM) drives based on a variable virtual resistance is proposed. In the proposed method, the inverter imitates variable resistance, this is used to suppress the inrush current and to regulate the small estimation current. Afterward, the speed and position of the motor are identified using the estimation current based on the fact that the load of the system becomes highly resistive as a result of a certain level of virtual resistance. Since high virtual resistance of the inverter could cause oscillations or instability to the system, we investigate a suitable region of virtual resistance values based on discrete stability analysis. Also, the estimation current controller and speed/position estimator are designed based on a linearized system. Since the proposed method does not require any motor parameters for the estimation process, the accuracy of the estimated position and speed is not affected by parameter variation. The controller design, region of virtual resistance, and facile implementation of the proposed method are shown to be effective by simulation and experiment.

20 January 2023 in Energies
Verified
Journal Article
Open access
PDF file
YLYoon-Seong Lee
Yoon-Seong Lee
KCKyoung-Min Choo
Kyoung-Min Choo
WJWon-Sang Jeong
Won-Sang Jeong
CLChang-Hee Lee
Chang-Hee Lee
JYJunsin Yi
Junsin Yi
CWChung-Yuen Won
Chung-Yuen Won
A virtual impedance-based flying start considering transient characteristics for permanent magnet synchronous machine drive systems is proposed. The conventional flying start based on virtual resistance (VR) assumes that the load of the system is resistive. However, the maximum value of VR, which is determined by the machine parameter and sampling frequency, is sometimes small. In this case, the load of the system is non-resistive. This assumption error causes an estimated position error and degrades transient characteristics. In the proposed method, algebraic-type virtual inductance (VI) is added to the estimation current regulator of the flying start based on VR. This change improves the accuracy of the estimated rotor position and the transient characteristics. In addition, the discrete-time system model of the proposed flying start method is given, the stability was analyzed considering the change in VR caused by the proposed method, and the improvements were verified by PSIM simulations and experimental results.

19 February 2020 in Energies
Verified
Journal Article
Open access
PDF file
KCKyoung-Min Choo
Kyoung-Min Choo
CWChung-Yuen Won
Chung-Yuen Won
In this paper, a model-based tuning method for a PID controller of excitation systems based on a simplified model that considers measurement delay is proposed. The conventional model-based tuning method, which has been studied previously, uses a simplified excitation system model that ignores all the delay components. However, since the rms voltage measurement can take hundreds of milliseconds to calculate depending on the system settings, this delay cannot be ignored when the required response needs to be as fast as the measurement delay. Furthermore, the linearity of the measurement method is not taken into account because the measurement delay has already been ignored. Therefore, in this paper, a simplified model that considers measurement delay and its linearity is proposed, and a model-based tuning method of PID controllers for two kinds of excitation systems is proposed and compared with the conventional method by analysis. To verify the analysis and proposed tuning method, experiments are conducted for both excitation systems.

17 March 2024 in Energies
Verified
Journal Article
Open access
PDF file
YLYoon-Seong Lee
Yoon-Seong Lee
KCKyoung-Min Choo
Kyoung-Min Choo
CLChang-Hee Lee
Chang-Hee Lee
CAChang-Gyun An
Chang-Gyun An
JYJunsin Yi
Junsin Yi
CWChung-Yuen Won
Chung-Yuen Won
In this article, a finite control set-model predictive control (FCS-MPC) with variable sampling time is proposed. A zero-voltage vector appears in the dead time between specific voltage vectors, resulting in an unintentionally large common-mode voltage. Herein, a large common-mode voltage was suppressed, and the load current was controlled using a voltage vector combination that did not cause a zero-voltage vector in dead time. Additionally, to improve the total harmonic distortion (THD) of the load current, the intersection of the predicted current and the command current by all the volage vectors (VVs) in the combination is confirmed. The VV where the intersection occurs is selected as the optimal VV. This optimal VV is applied to the point where the predicted current and the reference current intersect. The applicable range of the sampling time should be selected by considering the calculation time and number of switching. Through the proposed FCS-MPC strategy, not only can the common-mode voltage be limited to within ±Vdc/6, but an improved THD can also be obtained compared to the existing method using fixed sampling. The proposed method was verified through PSIM simulation and experimental results.

1 November 2019
Verified
Conference Paper
Closed access
WJWon-Sang Jeong
Won-Sang Jeong
KCKyoung-Min Choo
Kyoung-Min Choo
JLJae-Hyung Lee
Jae-Hyung Lee
CWChung-Yuen Won
Chung-Yuen Won