The research presented in this paper is part of a more significant effort to improve the dynamic and static performance of power generation systems using solar panels under specific climatic conditions. The solar panel can produce the greatest power only at the specified voltage and electric current levels. Environmental variables, such as random atmospheric oscillations, have a significant effect on the performance of a solar system connected to the network. Irradiation and ambient temperature are the two inputs to a PV (photovoltaic) system. Because solar radiation varies in nature, the PV system efficiency is low. To improve the efficiency of a solar PV system, several maximum power point tracking (MPPT) approaches are used. The purpose of this paper is to improve the performance of DC/DC chopper controllers and PV inverters in the face of abrupt climate change. To that end, the primary goal of this paper is to compare the following maximum power point search (MPPT) algorithms: the incremental conductance (IC) algorithm, the fuzzy logic (FL) algorithm, VSI controller, and the particle swarm optimization (PSO) strategy. These algorithms were evaluated in terms of efficiency, stability, and speed. A 100 kW PV system is design using MATLAB software 2021a version.
21 November 2023 in Materials Today Communications
Optimizing fuel injector geometry represents a critical pathway toward cleaner and more efficient diesel combustion. This study presents a comprehensive numerical investigation of the influence of the dual-hole nozzle injection angle on the primary atomization behavior and spray hydrodynamics of high-pressure diesel jets. The present analysis is deliberately restricted to cold-flow, near-nozzle primary breakup under isothermal conditions (293.15 K) so that the hydrodynamic and aerodynamic breakup mechanisms can be isolated in the immediate vicinity of the orifice before evaporation and combustion occur. Two-dimensional simulations are conducted using an Eulerian Volume-of-Fluid (VOF) framework with finite element discretization, three injection-angle configurations (0°, 5°, and 10°) under realistic engine conditions (injection pressure: 138 MPa; chamber pressure: 2.32 MPa; nozzle diameter: 100 µm). The numerical model was validated against the experimental and computational benchmark data of Ménard et al., showing reasonable qualitative agreement in jet morphology, although the 2D nature of the model leads to an exaggerated accumulation of liquid at the spray tip compared to the 3D reference. The validation therefore supports the qualitative trends and the relative angular comparison, but the absolute quantitative predictions remain subject to this 2D structural limitation. Results reveal that the injection angle exerts a decisive influence on the competition between axial momentum and radial dispersion. The neutral 0° configuration yields an overly concentrated jet with limited interfacial destabilization and poor air entrainment, whereas the 10° angle produces excessive radial spreading at the expense of axial penetration depth. By contrast, the 5° convergence angle provides the best trade-off among the three tested configurations under the studied conditions, promoting enhanced Rayleigh–Plateau instability growth, earlier ligament formation, and finer droplet generation—favorable to a more homogeneous air–fuel mixture. These findings provide quantitative guidance for dual-hole injector geometry design and demonstrate the suitability of high-fidelity VOF-based methods for resolving complex two-phase atomization phenomena relevant to low-emission diesel engine design. Quantitatively, the peak axial velocity is reached at the nozzle exit for all configurations; relative to the 0° baseline, the 5° convergence angle increases the fuel–air interfacial spreading by about 141% while retaining roughly 90% of its axial penetration at the monitoring positions P1–P3, whereas the 10° case loses about 26% of axial penetration for a comparable radial spread.
Access to clean drinking water is an increasing global challenge due to population growth, industrialization, and environmental deterioration. Solar stills have garnered attention as promising technologies for water purification because they are sustainable, environmentally friendly, and cost-effective. However, their performance is often limited by suboptimal thermal management and low evaporation rates. To address these limitations, this study develops a two-dimensional numerical model using COMSOL Multiphysics to investigate a double-slope solar still equipped with an actively rotating external reflector. The model simulates coupled heat and mass transfer processes and is validated against experimental data, enabling a comprehensive analysis of thermal behavior and distillate yield. Simulation results demonstrate that optimizing the reflector angle significantly enhances the temperature distribution within the desalination chamber, leading to a 9% increase in pond water temperature and a 5.5% rise in glass cover temperature. Moreover, adjusting the reflector's angle results in a 36.4% improvement in daily freshwater productivity. The simulation outcomes closely match the experimental findings, with a maximal deviation below 7%. In conclusion, the integration of an actively rotating external reflector substantially improves the performance of double-slope solar stills by maximizing solar flux concentration, boosting evaporation rates, and increasing overall output efficiency. This approach provides a promising strategy for sustainable and efficient freshwater production in regions with high solar irradiance.
31 December 2025 in Journal of Computing and Data Technology
Emotional voice conversion (EVC) aims to transform the emotional characteristics of speech while preserving speaker identity and linguistic content, and plays a critical role in affective computing, expressive speech synthesis, and human--computer interaction. Despite recent progress, existing EVC approaches often struggle to jointly model long-term temporal dependencies and achieve perceptually realistic spectral transformations, particularly in non-parallel training scenarios. To address these challenges, this paper proposes a high-fidelity emotional voice conversion framework that integrates Sequence-to-Sequence (Seq2Seq) temporal modeling with Cycle-Consistent Generative Adversarial Networks (CycleGAN). The proposed architecture operates entirely in the Mel-spectrogram domain. A Seq2Seq encoder--decoder with attention is first employed to capture long-range temporal dependencies and generate a coarse emotion-aware spectral representation. Subsequently, a CycleGAN-based refinement module enhances spectral realism and emotional expressiveness through adversarial and cycle-consistent learning, without requiring parallel emotional speech data. A neural vocoder is finally used to reconstruct the time-domain waveform from the refined Mel-spectrogram. The proposed framework is evaluated on the Emotional Speech Dataset (ESD) using objective metrics including Mel-Cepstral Distortion (MCD), fundamental frequency (Fo) root-mean-square error (RMSE), and structural similarity index (SSIM), along with subjective listening evaluations. Experimental results demonstrate that the proposed Seq2Seq--CycleGAN model outperforms conventional Seq2Seq-only and CycleGAN-only baselines in terms of emotional expressiveness, speech naturalness, and speaker similarity, confirming the effectiveness of jointly leveraging temporal modeling and adversarial spectral refinement for high-quality emotional voice conversion.