This study has focused on the PM emissions of diesel engines. Diesel engines are attractive power units that are used widely in many fields and have become one of the larger contributors of total petroleum consumption. However, diesel engines are among the main contributors of emissions into the air, especially particulate matter (PM) and nitrogen oxides (NOx). PM is one of the major pollutants emitted by diesel engines and has adverse effects on human health. Accordingly, many studies have been conducted to find alternative fuels that are clean and efficient. Biodiesel, which produces less PM than diesel fuel, is preferred as an alternative source for diesel engines. Therefore, using palm oil methyl ester (POME) for diesel engines would be a more economical and sustainable solution. This study has focused on the PM emissions of diesel engines fuelled by a diesel and POME blend (B5, B10, B20, and B100). A comparison between diesel and the POME blend has been made which involves PM mass concentration and its components (soluble organic fraction (SOF) and dry soot (DS)). Combustion characteristics, such as in-cylinder pressure and rate of heat release of the engine, as well as gaseous emissions, have also been observed at different operating engine loads (0.05 MPa 20%, 0.4 MPa 40%, and 0.7 MPa 60%). The results show that PM emissions of B100 are lower than those of diesel fuel owing to the oxygen content of POME. With regard to the SOF concentration, B100 has a higher SOF value than diesel fuel at all engine loads. Meanwhile, the DS for B100 is lower than that of diesel fuel. Moreover, as the engine load increased, PM and SOF concentrations increased, while DS concentration decreased. The observation of in-cylinder pressure showed that the increment of pressure with the increasing POME blend, as well as the increasing engine load due to the high cetane number for B100, led to a short ignition delay. The engine brake thermal efficiency between the POME blend and mineral diesel was comparable. Furthermore, B100 fuels showed lower engine power at higher brake-specific fuel consumption compared to other tested fuels. In terms of gaseous emissions, increasing POME blends led to an increase in NOx emissions. Meanwhile, as the engine load increased, NOx also continued to increase. The effect of the POME blend on the PM-NOx trade-off observation showed that B100 simultaneously increased the NOx and decreased the PM emissions. It can be concluded that POME creates a lower PM concentration while giving some negative feedback to NOx.

With its unique qualities, such as infinite supply, high octane number, and capacity to cut greenhouse gas emissions, alcohol is a viable alternative fuel for SI engines. This review article aims to reveal to readers the effects of alcohol on the performance, combustion behavior, and emission characteristics of SI engines by collecting the outcomes from previous research. This article looks at methanol, ethanol, and butanol fuel qualities. The performance of SI engines with butanol, ethanol, and methanol combined with gasoline is investigated in terms of brake torque, brake power, fuel consumption, thermal efficiency, volumetric efficiency, mean effective pressure, and coefficient of variation under various conditions. Second, in-cylinder pressure, mass fraction burnt, ignition delay, pressure increases, and heat release rates are also used to evaluate the combustion characteristic. Finally, the article discusses pollutant emissions such as CO, CO₂, NO_x, UHC, and exhaust gas temperature. Methanol, ethanol, and butanol mixed with gasoline increased fuel consumption and lowered spark-ignition engines’ thermal efficiency. When alcohol was combined with gasoline, most research found that CO, NO_x, and UHC emissions were reduced due to improved combustion.

A study on the application of oxygenated turpentine oil as a bio-additive in diesel fuel was conducted. The purpose of this research was to investigate the effect of oxygenated turpentine oil additive in diesel fuel on the performance and emission characteristics in diesel engines. Oxygenated turpentine oil is obtained from the oxidation process of turpentine oil. In this experimental study, the influences of oxygenated turpentine oil-diesel blended fuel OT0.2 (0.2% vol oxygenated turpentine oil and 99.8% vol diesel) were compared with pure diesel on engine performance, and emission characteristics were examined in a one-cylinder four-stroke CI engine. The test was performed at two engine loads (25% and 50%) and seven engine speeds (from 1200–2400 rpm with intervals of 200 rpm). The physiochemical characteristics of test fuels were acquired. The engine indicated power, indicated torque, fuel flow rate, and emissions (carbon dioxide, CO₂; carbon monoxide, CO; and nitrogen oxide, NO_X) were examined. The results revealed that the engine power shows slight increments of 0.7–1.1%, whereas the engine torque slightly decreased with oxygenated turpentine usage compared to pure diesel in most conditions. Furthermore, a reduction in NO_X emission decreased by about 0.3–66% with the addition of oxygenated turpentine in diesel compared to diesel. However, usage of OT0.2 decreased fuel flow rate in most speeds at low load but gave a similar value to diesel at 50% load. CO emissions slightly increased with an average of 1.2% compared to diesel while CO₂ emissions increased up to 37.5% than diesel. The high-water content, low cetane number, and low heating value of oxygenated turpentine oil were the reasons for the inverse effect found in the engine performances.

Diesel engine which is one of the larger contributors to total consumption for petroleum is an attractive power unit used widely in many fields. However, diesel engines are among the main contributors to air pollutions for the large amount of emissions, such as CO, CO₂ and NOx lead to an adverse effect on human health. Many researches have been done to find alternative fuels that are clean and efficient. Biodiesel is preferred as an alternative source for diesel engine which produces lower emission of pollutants. This study has focused on the evaluation of diesel and alcohol-diesel fuel properties and also the performance, combustion and exhaust emission from diesel engine fuelled with diesel and alcohol. Butanol and ethanol is blend with diesel fuel at 1:9 ratio. There are three test fuel that is tested which Diesel (100% diesel), D90BU10 (10% Butanol and 90% diesel) and D90E10 (10% Ethanol and 90% diesel). The comparison between diesel and alcohol-diesel blend has been made in terms of fuel properties characterization, engine performance such as brake power (BP) and brake specific fuel consumption (BSFC) also the in cylinder maximum pressure characteristic. Thus, exhaust gas emission of CO, CO₂, NOx and O₂ emission also has been observed at constant load of 50% but in different operating engine speed (1100 rpm, 1400 rpm, 1700 rpm, 2000 rpm and 2300 rpm). The results show the addition of 10% of each butanol and ethanol to diesel fuel had decreased the fuel density about 0.3% to 0.5% compared to mineral diesel. In addition, viscosity and energy content are also decrease. The addition of 10% butanol had improved the fuel cetane number however the ethanol blends react differently. In term of engine performance, as the engine speed increased, BP output also increase respectively. Hence, the alcohol blends fuel generates lower BP compared to diesel, plus BSFC for all test fuel shows decreasing trend at low and medium speed, however increased gradually at higher engine speed. Thus, D90BU10 had higher BSFC compared to mineral diesel and D90E10. In general, the addition of alcohol blend in diesel fuel had increase the BSFC. In term of in cylinder pressure, as the engine speed is increased, the crank angle noted to move away from TDC for all test fuel. The maximum cylinder pressure increased at low and medium speed, but decrease in higher engine speed. The addition of 10% of butanol and ethanol in the mineral diesel decreased the maximum cylinder pressure. Meanwhile, O₂ emission of D90E10 is higher compared to D90BU10 due to higher oxygen content found in ethanol. The CO₂ emission of D90BU10 recorded higher compared to mineral diesel due to the high oxygen contents in the alcohol. CO emission of alcohol blend on the other hand had lower emission at higher engine speed compared to mineral diesel. As engine speed is increased, NOx emission of mineral diesel and D90E10 had decreased gradually. However, D90BU10 had increased of NOx emission at lower to medium engine speed, than gradually decreased at higher engine speed.

In recent years, electric two-wheelers are emerging as one of the alternatives to improve the sustainability of transportation energy and air quality, especially in urban areas. Although electric two-wheeler motorcycles are environmentally friendly, they underperform compared with gasoline two-wheelers in many respects, particularly in speed and cruise distance between refuelling and recharging. Therefore, the engine development program can be done with a dynamometer. Variables such as the shape of torque and power curves can be analyzed. Hence, this project is aimed to develop a chassis dynamometer that can be used to measure mechanical power, speed and torque, and provide a controllable load to the electric motorcycle being tested. The prototype of chassis dynamometer for electric motorcycle had been developed and performance of the chassis dynamometer was tested by using an electric bicycle to emulate the basic performance requirements of an electric motorcycle which consist of maximum speed, driving range and acceleration.

The railway is an essential mode of transportation. Despite advances in railway safety over the past few decades, train accidents and incidents continue to be p