Antonio Bruno

Dr. Antonio Bruno


Research Focus & Metrics

Academic Career Length

36Years (1991-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2018 in Journal of Magnetism and Magnetic Materials
Verified
Journal Article
Closed access
MAMonica Arenas
Monica Arenas
RSRosa M. Silveira
Rosa M. Silveira
CPClara J. Pacheco
Clara J. Pacheco
ABAntonio Bruno
Antonio Bruno
JAJefferson Araujo
Jefferson Araujo
GPGabriela Pereira
Gabriela Pereira

1 April 1991 in Review of Scientific Instruments
Verified
Journal Article
Closed access
PDF file
ABAntonio Bruno
Antonio Bruno
PRP. Costa Ribeiro
P. Costa Ribeiro
When using multichannel SQUID magnetometers for biomagnetic applications, the correct measurement of the Tesla/volt calibration factor of each channel is of extreme importance, in order to avoid gross errors when analyzing the results. We propose a general calibration method valid for all kinds of gradiometer arrays. One of the main properties of this method is that the gradiometer position inside the cryogenic Dewar does not need to be known precisely. When tested, calibration factors with accuracies ranging from 0.3% to 0.8% were obtained. It is based on a spatial Fourier technique and on the fact that the gradiometer acts as a discrete spatial filter.

28 October 2023 in Sensors
Verified
Journal Article
Open access
PDF file
JPJoao Manoel Barbosa Pereira
Joao Manoel Barbosa Pereira
PGPaula Gouvêa
Paula Gouvêa
ABArthur Braga
Arthur Braga
ICIsabel Carvalho
Isabel Carvalho
ABAntonio Bruno
Antonio Bruno
The finite element method (FEM) was used to investigate the optical–mechanical behavior of a Fabry–Perot Interferometer (FPI) composed of a capillary segment spliced between two sections of standard optical fiber. The developed FEM model was validated by comparing it with theory and with previously published experimental data. The model was then used to show that the absolute strain on the host substrate is usually smaller than the strain measurement obtained with the sensor. Finally, the FEM model was used to propose a cavity geometry that can be produced with repeatability and that yields the correct absolute strain experienced by the host substrate, without requiring previous strain calibration.

6 June 2006 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
CFC.S. Franco
C.S. Franco
GRG.P. Ribas
G.P. Ribas
ABAntonio Bruno
Antonio Bruno

1 January 1998 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
ABAntonio Bruno
Antonio Bruno
LML. Couto Miranda
L. Couto Miranda
CHCARLOS HALL
CARLOS HALL
ELE. Andrade Lima
E. Andrade Lima
GKG.S. Kuhner
G.S. Kuhner
The generalized inverse method and singular value decomposition were used to reconstruct the magnetic image of small spherical inclusions in ferromagnetic structures. These techniques were used on the magnetic flux leakage generated when the structure is magnetized. The leakage field from the inclusions was simulated by using a simple constant-permeability model. The recovery model used a grid of magnetic dipoles at the region of the inclusions. The ability of the technique to distinguish between different distributions of inclusions with similar leakage fields is analyzed. The results demonstrates the feasibility of imaging multiple inclusions within the structure.

29 January 2022 in Brazilian Journal of Physics
Verified
Journal Article
Closed access
PDF file
JAJefferson Ferraz Damasceno Felix Araújo
Jefferson Ferraz Damasceno Felix Araújo
HCHélio Ricardo Carvalho
Hélio Ricardo Carvalho
SLSonia Renaux Wanderley Louro
Sonia Renaux Wanderley Louro
PRPaulo Edmundo de Leers Costa Ribeiro
Paulo Edmundo de Leers Costa Ribeiro
ABAntonio Bruno
Antonio Bruno