Paula Gouvêa

Dr. Paula Gouvêa

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 June 2016 in Optics Express
Verified
Journal Article
Open access
PDF file
Greice CostaGreice Costa
Greice Costa
PGPaula Gouvêa
Paula Gouvêa
LSLarissa M. B. Soares
Larissa M. B. Soares
JPJoão M. B. Pereira
João M. B. Pereira
FFFernando Favero
Fernando Favero
ICIsabel C. S. Carvalho
Isabel C. S. Carvalho
In this paper we discuss the results obtained with an in-fiber Fabry-Perot interferometer (FPI) used in strain and magnetic field (or force) sensing. The intrinsic FPI was constructed by splicing a small section of a capillary optical fiber between two pieces of standard telecommunication fiber. The sensor was built by attaching the FPI to a magnetostrictive alloy in one configuration and also by attaching the FPI to a small magnet in another. Our sensors were found to be over 4 times more sensitive to magnetic fields and around 10 times less sensitive to temperature when compared to sensors constructed with Fiber Bragg Grating (FBG).

31 October 2013 in Optics Express
Verified
Journal Article
Closed access
PDF file
ACAlexandre R. Camara
Alexandre R. Camara
PGPaula Gouvêa
Paula Gouvêa
ADAna Carolina M. S. Dias
Ana Carolina M. S. Dias
ABArthur M. B. Braga
Arthur M. B. Braga
RDRosa Fireman Dutra
Rosa Fireman Dutra
ICIsabel C. S. Carvalho
Isabel C. S. Carvalho
Dengue fever is a viral disease that affects millions of people worldwide. Specific tests for dengue are not usually performed due to high costs, complicated procedures and, in some cases, long time to yield a result. For widespread use of specific tests to be possible, fast, reliable and fairly simple methods are needed. In this paper, we present a new dengue diagnostic method for the acute phase of the infection. The method proposed uses an all-optical fiber sensor based on Localized Surface Plasmon Resonance (LSPR) and specular reflection from gold nanoparticles (AuNPs). Dengue anti-NS1 antibody was immobilized on AuNPs deposited on the endface of a standard multimode fiber (62.5µm/125µm). The sensor is able to detect NS1 antigen at different concentrations, with limit of quantification estimated to be 0.074 μg/ml = 1.54 nM. These results indicate that the sensor could potentially be used for dengue diagnosis in the acute phase of the infection.

21 February 2012 in Optics Express
Verified
Journal Article
Closed access
PDF file
ERE. C. Romani
E. C. Romani
DVDouglas Vitoreti
Douglas Vitoreti
PGPaula Gouvêa
Paula Gouvêa
PCP. G. Caldas
P. G. Caldas
RPR. Prioli
R. Prioli
ICIsabel Carvalho
Isabel Carvalho
Materials presenting high optical nonlinearity, such as materials containing metal nanoparticles (NPs), can be used in various applications in photonics. This motivated the research presented in this paper, where morphological, linear and nonlinear optical characteristics of gold NPs on the surface of bulk soda-lime glass substrates were investigated as a function of nanoparticle height. The NPs were obtained by annealing gold (Au) thin films previously deposited on the substrates. Pixel intensity histogram fitting on Atomic Force Microscopy (AFM) images was performed to obtain the thickness of the deposited film. Image analysis was employed to obtain the statistical distribution of the average height of the NPs. In addition, absorbance spectra of the samples before and after annealing were measured. Finally, the nonlinear refractive index (n2) and the nonlinear absorption index (α2) at 800 nm were obtained before and after annealing by using the thermally managed eclipse Z-scan (TM-EZ) technique with a Ti:Sapphire laser (150 fs pulses). Results show that both n2 and α2 at this wavelength change signs after the annealing and that the samples presented a high nonlinear refractive index.

28 October 2023 in Sensors
Verified
Journal Article
Open access
PDF file
JPJoao Manoel Barbosa Pereira
Joao Manoel Barbosa Pereira
PGPaula Gouvêa
Paula Gouvêa
ABArthur Braga
Arthur Braga
ICIsabel Carvalho
Isabel Carvalho
ABAntonio Bruno
Antonio Bruno
The finite element method (FEM) was used to investigate the optical–mechanical behavior of a Fabry–Perot Interferometer (FPI) composed of a capillary segment spliced between two sections of standard optical fiber. The developed FEM model was validated by comparing it with theory and with previously published experimental data. The model was then used to show that the absolute strain on the host substrate is usually smaller than the strain measurement obtained with the sensor. Finally, the FEM model was used to propose a cavity geometry that can be produced with repeatability and that yields the correct absolute strain experienced by the host substrate, without requiring previous strain calibration.

1 January 2018
Verified
Conference Paper
Closed access
PDF file
PGPaula Gouvêa
Paula Gouvêa
KMKhrissy A. R. Medeiros
Khrissy A. R. Medeiros
ARAlexandre S. Ribeiro
Alexandre S. Ribeiro
CHCARLOS HALL
CARLOS HALL
JDJosé R. M. D'Almeida
José R. M. D'Almeida
ABArthur M. B. Braga
Arthur M. B. Braga
We developed a non-intrusive flow sensor for pipe flow based on FBG and FIV. The standard deviation of the strain time series signal obtained by the FBG and the flow rate present a quadratic dependence.

28 August 2024 in Sensors
Verified
Journal Article
Open access
PDF file
ICIsabel Camerini
Isabel Camerini
LSLuis Paulo Brasil de Souza
Luis Paulo Brasil de Souza
PGPaula Gouvêa
Paula Gouvêa
ABArthur Braga
Arthur Braga
Acoustic waves can be used for wireless telemetry as an alternative to situations where electrical or optical penetrators are unsuitable. However, the response of the ultrasonic transducer can be greatly affected by temperature variations, mechanical deformations, misalignment between transducers, and multiple layers in the propagation zone. Therefore, this work sought to quantify such influences on communication between ultrasonic transducers. The experimental measurements were performed at the frequency where power transfer is maximized. Moreover, there were four experimental models, each with its own performed setup. The ultrasonic transducers are attached to both sides of a 6 mm thick stainless-steel plate for configuring just one barrier. Multiple layers of transducers are attached to the outer side of two plates immersed in an acoustic fluid with a 100 mm thick barrier. In both cases, the S21 parameter was used to quantify the influence of the physical barrier because it correlates with the power flow between ports that return after a given excitation. The results showed that when a maximum deformation of 1250 μm/m was applied, the amplitude of the S21 parameter varied around +0.7 dB. Furthermore, increasing the temperature from 30 to 100 °C slightly affected the S21 (+0.8 dB), but the signal decayed quickly for temperatures beyond 100 °C. Additionally, the ultrasonic communication with a multiple layer was found to occur under misalignment with an intersection area of up to 40%. None of the factors evaluated resulted in insufficient power transfer, except for a large misalignment between the transducers. Such results indicate that this type of communication can be a robust alternative, with a minimum alignment of 40% between transducers and electrical penetrators.