Polyglycolic acid (PGA) is used as a reinforcing component to enhance the mechanical properties of poly(ethylene glycol-co-cyclohexane-1,4-dimethanol terephthalate) (PETG). The tensile performance, micromorphology, crystallinity, heat resistance, and melt mass flow rates (MFRs) of PETG/PGA blends with varying PGA contents were studied. Both the tensile yield strength and tensile modulus of the PETG/PGA blends increased gradually with an increase in the PGA content from 0 to 35 wt%. The tensile yield strength of the PETG/PGA (65/35) blend increased by 8.7% (44.38 to 48.24 MPa), and the tensile modulus increased by 40.2% (1076 to 1509 MPa). However, its tensile ductility decreased drastically, owing to the poor interfacial compatibility of PETG/PGA and the oversized PGA domains. A multiple epoxy chain extender (ADR) was introduced into the PETG/PGA (65/35) blend to improve its interfacial compatibility and rheological properties. The tensile performance, micromorphology, rheological properties, crystallinity, and heat resistance of PETG/PGA (65/35) blends with varying ADR contents were studied. The strong chain extension effect of ADR along with its reactive compatibilization improved the rheological properties and tensile ductility. By carefully controlling the ADR concentration, the performance of PETG/PGA blends can be regulated for different applications.

This study investigated the impact of a multiple epoxy chain extender (ADR) on the rheological behavior, crystallization, and mechanical properties of polyglycolic acid (PGA). Tests of the torque and melt mass flow rate and dynamic rheological analysis were conducted to study the rheological behavior of PGA modified with ADR. The rheological results of the modified PGA showed a significantly increased viscosity and storage modulus with an increase in the ADR amount, which could be attributed to the chain extension/branching reactions between PGA and ADR. It was proved that ADR could be used as an efficient chain extender for tailoring the rheological performance of PGA. The Han plot of the modified PGA showed a transition of viscous behavior to elastic behavior, while the ADR content was increased from 0 to 0.9 phr. The formation of long-chain branches (LCBs) was confirmed via the Cole–Cole plot and weighted relaxation spectrum, wherein the LCBs substantially changed the rheological behavior of the modified PGA. The vGP plots predicted a star-type topological structure for the LCBs. The results of non-isothermal crystallization kinetics suggested that the crystallization of the modified PGA was predominantly homogeneous nucleation and three-dimensional growth. The crystallinity decreased slightly with the increase in the ADR amount. Compared to neat PGA, the modified PGA samples exhibited better tensile and flexural performances.

Highly toughened bio-based polylactic acid (PLA)/Eucommia ulmoides gum (EUG) blends were prepared using organic montmorillonite (OMMT) as a compatibilizer through melt-blending. Both the theoretically predicted values and the experimental results confirm that the majority of the OMMT’s nanolayers are selectively localized at the PLA/EUG interface. This localization leads to improved interfacial properties and a more refined morphology of the dispersed EUG phase. By increasing the OMMT content from 0 phr to 2 phr, the notched Izod impact strength of the PLA/EUG/OMMT (85/15/2) blend increases to a maximum value of 44.6 kJ/m². This is significantly higher than the values observed for neat PLA at 3.8 kJ/m² and the PLA/EUG (85/15) blend at 4.7 kJ/m². Moreover, compared to neat PLA and the PLA/EUG (85/15) blend, which exhibit poor tensile ductility, as indicated by their low elongation at break, the PLA/EUG/OMMT blend demonstrates a substantial improvement in its tensile ductility when an appropriate amount of OMMT is added. It is believed that the enhanced toughness of the PLA/EUG/OMMT blends can primarily be attributed to the refinement and more uniform dispersion of the EUG domains, which is caused by the incorporation of OMMT. In addition, the crystalline properties, thermal degradation behavior, and extrudate swell behavior of the PLA/EUG blends with and without OMMT were also evaluated in detail. Finally, the experimental results prove that the PLA/EUG (85/15) blend containing 2 phr of OMMT exhibits the highest impact toughness and tensile ductility, accompanied by improved thermal stability and extrusion stability.