Glass fiber-reinforced polymers (GFRPs) have received increasing attention in recent years due to their overall performance of light weight, low cost and corrosion resistance, and they are increasingly used as reinforcement in concrete structures. However, GFRP material has low elastic modulus and linear elastic properties compared with steel bars, which introduces different bonding characteristics between bars and concrete. Therefore, a reliable monitoring method is urgently needed to detect the bond slip in GFRP-reinforced concrete structures. In this paper, a piezoceramic-based active sensing approach is proposed and developed to find the debonding between a GFRP bar and the concrete structure. In the proposed method, we utilize PZT (lead zirconate titanate) as two transducers. One acts as an actuator which is buried in the concrete structure, and the other acts as a sensor which is attached to the GFRP bar by taking advantage of machinability of the GRRP material. Both transducers are strategically placed to face each other across from the interface between the GFRP bar and the concrete. The actuator provokes a stress wave that travels through the interface. Meanwhile, the PZT patch that is attached to the GFRP bar is used to detect the propagating stress wave. The bonding condition determines how difficult it is for the stress wave traveling through the interface. The occurrence of a bond slip leads to cracks between the bar and the concrete, which dramatically reduces the energy carried by the stress wave through the interface. In this research, two specimens equipped with the PZT transducers are fabricated, and pull-out tests are conducted. To analyze the active sensing data, we use wavelet packet analysis to compute the energy transferred to the sensing PZT patch throughout the process of debonding. Experimental results illustrate that the proposed method can accurately capture the bond slip between the GFRP bar and the concrete.

Some of the most severe structural loadings come in the form of blast loads, which may be caused by severe accidents or even terrorist activities. Most commonly after exposure to explosive forces, a structure will suffer from different degrees of damage, and even progress towards a state of collapse. Therefore, damage detection of a structure subject to explosive loads is of importance. This paper proposes a new approach to damage detection of a concrete column structure subjected to blast loads using embedded piezoceramic smart aggregates (SAs). Since the sensors are embedded in the structure, the proposed active-sensing based approach is more sensitive to internal or through cracks than surface damage. In the active sensing approach, the embedded SAs act as actuators and sensors, that can respectively generate and detect stress waves. If the stress wave propagates across a crack, the energy of the wave attenuates, and the reduction of the energy compared to the healthy baseline is indicative of a damage. With a damage index matrix constructed by signals obtained from an array of SAs, cracks caused by blast loads can be detected throughout the structure. Conventional sensing methods such as the measurement of dynamic strain and acceleration were included in the experiment. Since columns are critical elements needed to prevent structural collapse, knowledge of their integrity and damage conditions is essential for safety after exposure to blast loads. In this research, a concrete column with embedded SAs was chosen as the specimen, and a series of explosive tests were conducted on the column. Experimental results reveal that surface damages, though appear severe, cause minor changes in the damage index, and through cracks result in significant increase of the damage index, demonstrating the effectiveness of the active sensing, enabled by embedded SAs, in damage monitoring of the column under blast loads, and thus providing a reliable indication of structural integrity in the event of blast loads.

Timber structures have been widely used due to their low-cost and environmental-friendly properties. It is essential to monitor connection damage to ensure the stability and safety of entire timber structures since timber connection damage may induce catastrophic incidents if not detected in a timely manner. However, the current investigations on timber connections focus on mechanical properties and failure modes, and the damage detection of timber connection receives rare attention. Therefore, in this paper, we investigate the damage detection of four common timber connections (i.e., the screw connection, the bolt connection, the decussation connection, and the tooth plate connection) by using the active sensing method. The active sensing method was implemented by using a pair of lead zirconate titanate (PZT) transducers: one PZT patch is used as an actuator to generate stress waves, and the other works as a sensor to detect stress waves after propagating across the timber connection. Based on the wavelet packet energy analysis, the signal energy levels of received stress waves under different damage extent are quantified. Finally, by comparing the signal energy between the intact status and the damage status of the timber connection, we find that the energy attenuates with increasing severity of the connection damage. The experimental results demonstrate that the active sensing method can realize real-time monitoring of timber connection damage, which can guide further investigations.

Two identically sized RC beams were fabricated to investigate the effects of explosive loads on the flexural behaviour of Reinforced Concrete (RC) beams. One of the beams was subjected to an explosive load to induce post-explosion damage, and subsequently, both beams underwent flexural capacity testing. Integrating piezoelectric smart aggregates (SAas) within the beams facilitated continuous observation of the damage conditions, allowing for the assessment of internal concrete deterioration from explosive impacts to bending failures. The internal crack development index R was established using the Wavelet Packet Energy Analysis method. Combined with the structure’s residual capacity-based damage assessment criterion, the relationship between R and component damage was found. This allowed us to identify the change in the bending capacity of RC beams after explosion damage and the quantitative damage assessment of the beam to be realised, providing valuable insights for structural engineers and researchers. Comparing the flexural test results between the explosively pre-damaged beam and the undamaged test beam, it was observed that the neutral axis of the damaged beam was significantly elevated, accompanied by a notable reduction in flexural capacity. By examining the variation curve of the internal crack development index R, it was noted that during the initial stage of the bending flexural test, due to bending deformation, cracks in the core region of the pre-damaged beam gradually healed, leading to a pseudo-decrease in the damage index. After reaching a minimum point, the damage progressed faster until failure occurred.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.