In this article, a novel sensorless control for permanent magnet synchronous machine (PMSM) using its radiated acoustic noise is proposed in which a high-frequency voltage signal is superimposed upon the fundamental excitation and the machine response to such excitation is studied. First, the analytical equations describing the field formation within the airgap leading to the generation of radial forces and acoustic noise are extensively investigated. In the next step, resulting harmonics in the acoustic noise waveform caused by the injected signals are predicted. Then it is experimentally verified that, depending on the machine structure, there will be some distinctive sidebands around the injected frequency directly related to the fundamental synchronous frequency. Acoustic noise waveform is highly distorted and sensitive to the environment; so a proposed four-stage signal processing algorithm containing two self-adaptive band-pass filters are used to safeguard the signal against unwanted distortions and flawlessly extract the rotor position information. Robustness and effectiveness of this method are verified experimentally in various operating conditions.
The paper presents a Level-Set based topology optimization method for improving the magnetic torque of electrical motors such as synchronous reluctance machines using a 2D magnetostatic finite element context modelling. The novelty is the use of a fully analytical expression for the torque sensitivity analysis based on the virtual work principle which is more accurate and general than other methods, and its application to a Level-Set implementation. The numerical study of a synchronous reluctance machine is presented. Then, the Level-Set method is detailed in a general context. The corresponding analytical continuous sensitivity analysis using the adjoint method to maximize the torque is expressed and validated. Finally, the application to the optimization of the rotor of a synchronous reluctance machine is shown to illustrate the efficiency of the method.
7 May 2019 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Purpose: The thermal modelling of an electrical machine is difficult because the thermal behavior depends on its geometry, the used materials and its manufacturing process. In the paper, such a thermal model is used during the sizing process by optimization of a hybrid electric vehicle (HEV). This paper aims to deal with the sensitivities of thermal parameters on temperatures inside the electrical machine to allow the assessment of the influence of thermal parameters that are hard to assess. Design/methodology/approach: A sensitivity analysis by Sobol indices is used to assess the sensitivities of the thermal parameters on electrical machine temperatures. As the optimization process needs fast computations, a lumped parameter thermal network (LPTN) is proposed for the thermal modelling of the machine, because of its fastness. This is also useful for the Sobol method that needs too many calls to this thermal model. This model is also used in a global model of a hybrid vehicle. Findings: The difficulty is the thermal modelling of the machine on the validity domain of the sizing problem. The Sobol indices allow to find where a modelling effort has to be carried out. Research limitations/implications: The Sobol indices have a significant value according to the number of calls of the model and their type (first-order, total, etc.). Therefore, the quality of the thermal sensitivity analysis is a compromise between computation times and modelling accuracy. Practical implications: Thermal modelling of an electrical machine in a sizing process by optimization. Originality/value: The use of Sobol indices for the sensitivity analysis of the thermal parameters of an electrical machine.
4 May 2012 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Purpose – An analytical approach is preferred to carry out the harmonic modelling of power electronics converters because it is generally faster than time simulation chained with FFT. However, the difficulty of such an approach is to build the model and to manage the uncontrolled commutations that occur in the studied static converter, and also to deal with large equations. The purpose of this paper is to propose an aid in the frequency modelling of the drive elements, in the frequency domain, including all key parameters for sizing aim i.e. a way to optimize the EMC filter using different algorithms.Design/methodology/approach – The paper aims to propose an aid to create such models, and to assure its good solving, i.e. that the correct operating mode is represented. So, the solving problem is formulated as an optimization problem under constraints, to solve this difficulty.Findings – The difficulty is to be sure to deal with the good operating mode of the static converter when soft or uncontrolled commu...
27 September 2023 in IEEE Transactions on Power Electronics
This article introduces an injectionless approach for acoustic-noise-based sensorless control of the permanent magnet synchronous machine. Replacing the high-frequency injection, the pulsewidth modulation (PWM) voltages are used as the basis for the method implementation. The mathematical model of PWM with considering the deadtime effect is first presented. Then, its impact upon the harmonics of current, magnetic fields, and generated radial forces is detailed. It is experimentally verified that in the presence of deadtime, unlike the contaminated current profile, there are merely specific-order speed-dependent components appeared in the acoustic noise spectrum, which is a clear bonus for signal processing precision and estimation performance. Moreover, a novel phase-locked loop (PLL) topology comprising a resonant-controller-based feedforward compensation block (RCPLL) is proposed. This compensation block is integrated within the PLL, by which the extra harmonics in the PLL error are directly suppressed, and therefore, the estimation performance is noticeably enhanced. The robustness of the proposed sensorless algorithm, alone, is verified experimentally under different conditions, and then, the estimation performances with and without the proposed RCPLL are compared.
17 March 2016 in COMPEL - The international journal for computation and mathematics in electrical and electronic engineering
Purpose – Static converters generate current harmonics in grids. Numerous studies on analytical frequency models of converters are often required to carry out their harmonic modeling in the context of sizing by optimization. Some formulations are proposed to solve such models. Each formulation has its own advantages and drawbacks. The paper mainly focusses on two formulations: the first to be solved by sequential quadratic programming (SQP) and the second to be solved by Newton-Raphson (NR). In this way, the purpose of this paper is to present the performances of each formulation and compare the results of both formulations for the modeling of a single-phase diode rectifier. Design/methodology/approach – The paper aims to compare SQP formulation and NR formulation, and to propose the ways to improve their convergence. In the modeling, by using an explicit formulation of the state variables combined to a numerical method, equations are defined to reduce, as far as possible, the number of unknowns. Findings...