A full lignin-to-chemicals valorisation chain – from hardwood over bissyringols to aromatic polyesters (APEs) – is established for renewable 4-n-propylsyringol (PS), the main product from catalytic hydrogenolysis of (native) hardwood lignin. To do so, reagent-grade PS was produced from birch wood via reductive catalytic fractionation (RCF) and isolated in 34 wt% yield on lignin basis. Additional early-stage theoretical calculations, based on both relative volatility (α) and distillation resistance (Ω) as well as Aspen Plus® simulations, predict that the isolation of PS by means of distillation is economically feasible at industrial scales ($85–95 per ton of propylphenolics at 200–400 kt a−1 scale). Subsequent stoichiometric acid-catalysed condensation with formaldehyde unveils a remarkably high 92 wt% selectivity towards the dimer 3,3′-methylenebis(4-n-propylsyringol) (m,m′-BSF-4P), which is isolated in >99% purity by facile single-step crystallisation. The striking dimer selectivity is ascribed to the synergetic interplay between the activating methoxy groups and the oligomerisation-inhibiting propyl chain. Next, an in vitro human oestrogen receptor α (hERα) assay was performed to ensure safe(r) chemical design. The bissyringyl scaffold displays reduced potency (∼19–45-times lower affinity than bisphenol A) and lower efficacy (∼36–45% of BPA's maximum activity). Lastly, to assess the functionality of the safe(r) bissyringol scaffold, it was converted into an APE. The APE displays a Mw = 43.0 kDa, Mn = 24.4 kDa, Tg = 157 °C and Td,5% = 345 °C. In short, (i) the feasibility and scalability of the feedstock, (ii) the simplified process conditions, (iii) the reduced in vitro oestrogenicity, and (iv) the functionality towards polymerisation, make this bissyringol a renewable and potentially benign bisphenol replacement, capable for production at bulk scale.
The increasing food demand for a growing population has resulted in the intensification and modernization of agriculture leading to an increasing use of pesticides to protect crops against insects, weeds, fungi, and other pests. These chemical compounds are time-persistant as they usually report low biodegradability and can cause adverse effects on the environment due to their toxicity. This study assesses the use of membranes designed for urban wastewater and drinking water treatment -DuPont FilmTec™ NF270 and FilmTec™ XLE membranes- for the removal of six pesticides (atrazine, simazine, isoproturon, metolachlor ESA, 2,4-D, and chlorothalonil) from aqueous streams. The results reported average rejection rates of 29–89% in the case of nanofiltration membranes and > 97% for reverse osmosis membranes. In addition, it was observed adsorption of pesticides within membranes’ active layer, which should be taken into account for the assessment of membranes performance when a fresh membrane is used. From this study can be concluded that membrane-based technology is effective for the removal of these pollutants from aqueous streams, but a customised selection of the membrane (nanofiltration/reverse osmosis) should be performed depending on the targeted pollutants in order to balance the pesticide rejection and energy consumption for each market application.
Microplastics are an increasing concern due to their widespread occurrence in aquatic environments worldwide. The lack of a harmonised protocol for their reliable quantification remains a major challenge in current scientific efforts. This study presents a comparative evaluation of three protocols for the detection and quantification of microplastics in aqueous samples. The protocols were assessed based on quantification efficiency, risk of particle degradation, staining performance, operational complexity, and cost per sample. Protocol A combined Rhodamine B and ethanol staining with NaCl-based density separation, demonstrating strong isolation performance while maintaining minimal chemical hazards and moderate cost (2.45€ per sample) that could be further reduced to 0.45€ per sample by substituting reagent-grade NaCl with table salt. Protocol B offered moderate isolation capacity and presented the highest risk of particle fragmentation, likely due to the use of acetone and high-temperature digestion. Protocol C, based on the combined use of Nile Red and ZnCl2, also presented a risk of particle fragmentation, resulting in the highest MP count for small and hydrophobic particles. In addition, its high cost (15.23€ per sample) limits its suitability for routine application.
Water scarcity has driven the use of wastewater treatment plant (WWTP) effluents as reclaimed water, highlighting the need to overcome challenges such as the presence of emerging contaminants, particularly microplastics (MPs), which WWTPs are unable to effectively remove. Membrane-based processes, such as microfiltration, have demonstrated high efficiency in the removal of suspended solids, and their application for MP removal is currently under investigation. This study assesses the influence of microfiltration membrane spacer size (1 mil and 80 mil) and geometry—diamond and corrugated—on MP recovery performance, using synthetic wastewaters with varying MPs concentrations. The results indicate the superior performance of large corrugated and small diamond-shaped membranes, as both exhibited the highest and comparable permeate flux, with no MP retention within the membrane element. All microfiltration membranes achieved an 80% recovery of the influent as safe reclaimed water and demonstrated an MP recovery efficiency exceeding 99%, with 100% rejection for fragments and up to 98% rejection for fibres.
19 September 2024 in Journal of Environmental Management