Type IV hydrogen storage cylinders are pivotal for high-pressure hydrogen storage and transportation, offering advantages such as lightweight design, high hydrogen storage density, and cost efficiency. Polyamide 6 (PA6) has emerged as a promising liner material due to its excellent mechanical strength, chemical resistance, and gas barrier properties. However, challenges remain, including high hydrogen permeability and insufficient mechanical performance under extreme temperature and pressure conditions. This review systematically summarizes recent advances in modification strategies to enhance PA6’s suitability for Type IV hydrogen storage cylinders. Incorporating nanofillers (e.g., graphene, montmorillonite, and carbon nanotubes) significantly reduces hydrogen permeability. In situ polymerization and polymer blending techniques improve toughness and interfacial adhesion (e.g., ternary blends achieve a special increase in impact strength). Multiscale structural design (e.g., biaxial stretching) and process optimization further enhance PA6’s overall performance. Future research should focus on interdisciplinary innovation, standardized testing protocols, and industry–academia collaboration to accelerate the commercialization of PA6-based composites for hydrogen storage applications. This review provides theoretical insights and engineering guidelines for developing high-performance liner materials.
With the rapid progression of industrialization, water pollution has emerged as an increasingly critical issue, especially due to the release of organic dyes such as methylene blue (MB), which poses serious threats to both the environment and human health. Developing efficient photocatalysts to effectively degrade these pollutants is therefore of paramount importance. In this work, titanium dioxide (TiO2) was modified with the photosensitizer hemin and the hydroxyl-rich polymer polydopamine (PDA) to enhance its photocatalytic degradation performance. Hemin and PDA function as photosensitizers, extending the light absorption of TiO2 into the visible spectrum, reducing its bandgap energy, and effectively promoting separation of photogenerated electron–hole pairs through conjugated structures. Additionally, the strong adhesion of PDA enabled the rapid transfer and effective utilization of photogenerated electrons, while its abundant phenolic hydroxyls increased MB adsorption on the photocatalyst’s surface. Experimental results demonstrated a significant enhancement in photocatalytic activity, with the 1%PDA/3%hemin/TiO2 composite achieving degradation rates of 91.79% under UV light and 71.53% under visible light within 120 min, representing 2.22- and 2.05-fold increases compared to unmodified TiO2, respectively. This research presents an effective modification approach and provides important guidance for designing high-performance TiO2-based photocatalysts aimed at environmental remediation.
Epoxy-terminated hyperbranched polymers (EHBPs) are a class of macromolecular polymers with a hyperbranched structure containing epoxy groups. They possess characteristics such as low viscosity, high functionality, and thermal stability, which endow them with broad application potential in materials science and chemical engineering. This study uses epoxidized soybean oil (ESO) as the raw material, which undergoes ring-opening reactions with glycerol and is esterified with 2,2-bis(hydroxymethyl)propionic acid (DMPA) to obtain epoxy soybean oil polyol (EGD) with a high hydroxyl value. Subsequently, four types of EHBPs are synthesized by incorporating epichlorohydrin (ECH) in mass ratios of 1:3, 1:4, 1:5, and 1:6 under strong alkaline conditions. The product structure is characterized using FT–IR and GPC. The degree of branching of EGD is calculated using 1H NMR and 13C NMR spectroscopy. The epoxy value of EHBPs is tested using the hydrochloric acid–acetone method, and the water contact angle, adhesion properties, rheological properties, and thermal properties of the EHBPs are also evaluated. The results show that the degree of branching of EGD is 0.45. The epoxy values of the EHBPs are 0.73, 0.79, 0.82, and 0.89 mol/100g, respectively. As the epoxy value and molecular weight of the epoxy hyperbranched polymers (EHBPs) increase, the water contact angle and adhesion strength of the EHBPs rise progressively and the viscosity decreases. Additionally, the glass transition temperature increases with the increase in the epoxy value. These epoxy hyperbranched polymers with low viscosity and high adhesion strength offer a promising approach for modifying surface coatings or formulating adhesives.
Integrating rubber with superior low-temperature capabilities, such as ethylene propylene diene monomer (EPDM), is a strategic approach to bolster the low-temperature performance of fluoroelastomer (FKM). However, FKM and EPDM are thermodynamically incompatible. This work synthetized three EPDM-based polar macromolecular compatibilizers, epoxidized EPDM (EPDM-EP), 2,2-trifluoroethylamine-grafted epoxidized EPDM (EPDM-TF), and 2,4-difluorobenzylamine-grafted epoxidized EPDM (EPDM-DF), to enhance the compatibility between FKM and EPDM. These compatibilizers were subsequently incorporated into FKM/EPDM rubber blends. The results revealed that the glass transition temperature (Tg) of FKM/EPDM decreased by 1.3 °C, 2.68 °C, and 2.78 °C, respectively, upon the addition of 10 phr of EPDM-EP, EPDM-TF, or EPDM-DF. Moreover, the Tg of the two phases converged. The tensile strength, elongation at break, and tear strength of the FKM/EPDM rubber blends were also enhanced by the inclusion of these compatibilizers. Notably, EPDM-TF and EPDM-DF exhibited remarkable compatibilization effects due to an increase in polarity. This research not only sheds light on the potential for developing new compatibilizers but also paves the way for innovative applications of FKM and its derivatives.
Polycaprolactone (PCL) is a widely used polymer in biomedical applications due to its excellent processability, ductility, and biodegradability. However, single-component PCL devices often fail to meet the multifunctional and high-performance demands of modern biomedical devices. In this study, we introduced biodegradable and environmentally friendly cyclodextrin (CD) to fabricate CD inclusion complexes with low-molecular-weight polycaprolactone (LPCL). These complexes were incorporated into commercial PCL to prepare the resulting composites. The effects of PCL molecular weight and CD type on the properties and inclusion ratios of the complexes were systematically investigated. Among the tested complexes, the one formed with LPCL (Mw = 8 × 104) and α-CD exhibited the highest inclusion ratio (2:1), significantly enhancing the crystallization and mechanical properties of the resulting composite (PCL/8-α-CD). Compared to pure PCL, the PCL/8-α-CD composite shows a 14.8% increase in crystallinity, along with improvements of 63.6% and 30.9% in tensile strength and elongation at break, respectively. These results demonstrate that the incorporation of CD inclusion complexes can effectively enhance the mechanical performance of PCL, making it a promising candidate for high-performance biomedical applications.