Ilias Reddah

Dr. Ilias Reddah


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 April 2025 in Coatings
Verified
Journal Article
Open access
PDF file
IRIlias Reddah
Ilias Reddah
LGLaala Ghelani
Laala Ghelani
STSofiane Touati
Sofiane Touati
FLFarid Lekmine
Farid Lekmine
PHPavol Hvizdos
Pavol Hvizdos
Haithem BOUMEDIRIHaithem BOUMEDIRI
Haithem BOUMEDIRI
In this work, an experimental investigation is conducted with the aim of optimizing the electrodeposition parameters for Ni-Al2O3 composite coatings using the Taguchi method. The presented research is structured into two complementary sections. The first segment investigates the characteristics of Ni and Ni-Al2O3 coatings, specifically Al2O3 particle incorporation and crystallinity variations, using X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and hardness evaluation through micro-indentation testing. The second section uses statistical techniques, specifically Analysis of Variance (ANOVA) and signal-to-noise (S/N) ratio analysis, to determine which parameters have the most impact on the experimental results. ANOVA and the Response Surface Methodology (RSM) were used in a modeling technique to forecast and optimize the technical responses. Based on an L16 orthogonal design, sixteen tests were carried out to investigate the effects of several important variables, including agitation rate (200–350 rpm), deposition period (15–60 min), alumina concentration (10–25 g.L−1), and current density (2–5 A.dm−2). The conditions for optimizing microhardness (HV) and Al2O3 integration while limiting average crystallite size (ACS) were identified using the most suitable function. The obtained results reveal significant improvements in the composite coating’s properties, including a 164% increase in microhardness, a 400% rise in alumina incorporation, and a notable reduction in crystallite size, demonstrating the efficacy of the electrodeposition process and optimization strategy adopted.

5 February 2026 in Coatings
Verified
Journal Article
Open access
PDF file
IRIlias Reddah
Ilias Reddah
LGLaala Ghelani
Laala Ghelani
DSDaniela Santo
Daniela Santo
JNJoana Neiva
Joana Neiva
LFLuís Figueiredo
Luís Figueiredo
Susana DevesaSusana Devesa
Susana Devesa
The present work investigates the effect of phosphorous-acid-induced pH variation on the electrodeposition of Ni–P coatings and examines how changes in electrolyte composition influence current efficiency, deposition behaviour, microstructure, optical properties, tribological response and wettability. In addition, the study assesses the potential of a post-deposition surface modification using stearic acid to enhance the hydrophobic character of the coatings. Ni and Ni–P layers were electrodeposited on 316L stainless steel using electrolytes containing 0–40 g/L of H3PO3, resulting in progressively lower bath pH and significant changes in deposition kinetics. The introduction of H3PO3 caused a sharp reduction in cathodic current efficiency and deposition rate, producing ultrathin Ni–P films with 20–24 at.% P. XRD and SEM analyses showed a transition from highly crystalline Ni to amorphous, nodular Ni–P structures. Tribological tests revealed a pronounced improvement in sliding performance for all Ni–P coatings compared to pure Ni, with sample S2 (5 g/L of H3PO3) exhibiting the lowest and most stable friction coefficient (~0.30). Wettability studies indicated that all as-deposited Ni–P surfaces were weakly hydrophobic, with surface energies dominated by the dispersive component. A stearic acid post-treatment produced a measurable increase in the water contact angle, indicating successful surface functionalization of the coatings. Overall, this study provides a comprehensive assessment of how phosphorous acid concentration governs the functional behaviour of electrodeposited Ni–P coatings.