There are often greater risks in the process of tunnel construction, and because of the unpredictable tunnel features, the risks during tunnel operation are also great. Due to the substantial growth of TTAs during the recent years, the safety issues of the tunnel traffic accidents (TTAs) have become a widely discussed topic in China. This study examined 2703 TTAs that occurred in the expressway tunnels of China, from 2001 to the present. The datasets from these accidents were analyzed in detail to determine the temporal and spatial characteristics of the traffic accidents as well as the source of the traffic accident distributions in the expressway tunnels. According to the analysis results, 58% of TTAs took place in the entrance and exit zones, and the rear end accident is the most common accident. In addition, the special festivals are liable to traffic accidents, especially during the Chinese Spring Festival. In order to reduce the accidents, special traffic service needs to be taken in key periods, the expressway tunnel operation departments should improve the management rules, and all the drivers should be educated to be more careful when they enter the tunnel.
The deformation characteristics of a weak foundation with high back siltation in an immersed tunnel lack empirical data; however, the calculation method and control of foundation settlements are highly important to tunnel design and construction. This paper takes a cross section of the natural foundation of an immersed tunnel in the Hong Kong‐Zhuhai‐Macao Bridge (HZMB) as the research object and conducts a centrifuge model test. The soil layer is divided, and the soil parameters are determined by the CPTU and the indoor dynamic three triaxial test. In consideration of the actual engineering scale and the ability of the centrifuge model test system, the similarity ratio of the model to the prototype is studied and determined. As for the immersed tube structure, the deformation characteristics are mainly studied. Therefore, the organic glass is selected as the model material by the similarity of the elastic modulus and the density. The characteristics of the resilience and recompression of the natural foundation of the immersed tunnel and the strain characteristics of the immersed tube structure are obtained by the analysis of the multiworking condition test data. Moreover, based on the actual engineering geological conditions of the subsea tunnel, a numerical calculation method is carried out to check the reliability of the centrifuge model test results. The results of the numerical calculation are consistent with the model test results.
The use of the segmental pipe section immersed tunnel suffers from several problems, such as complex construction, weak foundation, great water depth, great thickness of siltation back on the top of the tube, and difficult settlement control. Based on Winkel’s elastic foundation beam theory, a mechanical calculation model is established according to the case of an inhomogeneous soil layer, and the force and deformation of the structural system of the immersed tube tunnel are calculated based on a bridge in Zhuhai as an example of an immersed tube tunnel. The results show that the derived formula for calculating the allowable differential settlement per unit length of the longitudinally immersed tube is applicable to the sudden change type foundation stiffness deformation model of the natural foundation section of the tube tunnel of the aforementioned bridge in Zhuhai. The relationship between the settlement control index and related influencing factors is analyzed. Hence, a formula for calculating the stratified ground foundation’s integrated bed coefficient is derived, and the equations for tunnel deflection curves and shear forces are solved. A set of calculation methods that are applicable to the foundation settlement control criteria of the segmental immersed tunnel is provided, and the results provide a significant reference for the optimization of the foundation scheme and improvement of the construction process for similar projects.
Traditional soil subgrades are prone to stability degradation under long-term wet–dry cycling, where repeated moisture fluctuations induce microstructural damage and consequently reduce soil strength. To mitigate this stability degradation, this study proposes a composite layered subgrade structure with enhanced drainage performance. By incorporating a graded gravel drainage layer with a permeability coefficient multiple orders of magnitude higher than that of soil, a multi-tiered water diversion and drainage synergy system was established. Based on the Tianqiong Expressway project in Qionglai, Sichuan, field immersion tests were conducted with embedded temperature-humidity sensors and settlement plates. Combined with data from a distributed sensor network, the spatiotemporal evolution of volumetric water content across structural layers during immersion-drainage cycles was systematically investigated. Experimental results demonstrate: the layered structure stabilizes Subgrade moisture within an optimal range, whereas soil moisture in non-drained foundations increased from 28.1 to 41.6%, confirming severe water retention; The graded gravel layer enhances lateral drainage, reducing upper soil moisture through hydraulic gradient optimization and seepage path multiplication, achieving rapid water redistribution and stabilizing subgrade humidity. These findings elucidate the regulatory mechanism of composite layered structures on subgrade water retention states, providing critical design parameters for drainage layers in highway subgrade engineering. The proposed system significantly improves the long-term service performance of road infrastructure in humid, rainfall-intensive regions.
Exploring strain localization has substantial potential to significantly impact the disaster resilience and mitigation capabilities of infrastructure, thus influencing project sustainability. Consequently, the field of sustainable geotechnical engineering is progressively directing attention toward studying soil strain localization. This research focuses on triaxial testing to deepen our understanding of this phenomenon by applying discrete element methods, thereby fostering the advancement of sustainable geotechnical engineering practices. While rigid-wall-based discrete element triaxial tests have been extensively studied, using flexible boundaries in these tests has received limited attention. This study introduces a three-stage method to enhance stress application in flexible membranes by applying confining pressure. A comparison of triaxial tests was conducted at both macroscopic and microscopic scales, utilizing flexible and rigid boundaries. Moreover, numerical simulations were performed on flexible membrane samples with various particle sizes to identify appropriate dimensions for flexible boundaries. Our results demonstrate that the improved flexible membrane provides more accurate representations of macroscopic and microscopic sample variations than rigid walls. Keeping the particle sizes for flexible membranes within the range of 0.2 to 0.8 times the characteristic particle size (r) is essential for striking a balance between simulation accuracy and computational efficiency. These findings enhance the accuracy of triaxial compression test simulations and offer a valuable foundation for studying strain localization in soils. Understanding these phenomena is essential for various geotechnical engineering applications, such as foundation design and slope stability analysis. Furthermore, these findings form a pivotal foundation for resource optimization and enhancing the reliability of engineered structures, thereby driving the advancement of sustainable geotechnical engineering practices.