Tadeusz Smolnicki

Prof. Tadeusz Smolnicki

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2017 in Archive of Mechanical Engineering
Verified
Journal Article
Open access
PDF file
DGDominik Gunia
Dominik Gunia
TSTadeusz Smolnicki
Tadeusz Smolnicki
This paper presents the current study of the distribution of stresses for four-point contact wire race ball bearing. The main aim of this article is to define the most important geometrical rules in a wire-race bearing. The results for bearings of different geometrical parameters are presented. In the study, one also estimates the distribution of internal pressure in particular bearing elements.

14 October 2021 in Energies
Verified
Journal Article
Open access
PDF file
PSPiotr Sokolski
Piotr Sokolski
TSTadeusz Smolnicki
Tadeusz Smolnicki
Failure of systems applied in machines comprising rolling and slewing bearings usually causes downtime of the entire heavy machine. The problem of failures can be aggravated by extremely difficult operating conditions, such as significant loads or a harsh environment. The entire issue inspired us to develop a method of monitoring the condition of such units. A study was carried out for six different large-scale excavators which examined strain distributions in the tested subassemblies. In order to estimate the technical condition of wheeled bogies, we used the phenomenon of strain propagation caused by the concentrated force acting in the ring girder web. Flamant theory was utilized to describe this phenomenon. Measurements were performed using strain gauges and the obtained results were compared with the FEM model. To determine whether bearing joints were in a good or bad condition, a coefficient of variation and an impulse factor were introduced as diagnostic indicators. It turned out that by evaluating these indicators, it was possible to distinguish between these two conditions. The method was successfully validated on machines that are in operation.


4 March 2019 in AIP Conference Proceedings
Verified
Conference Paper
Closed access
PDF file
MKMariusz Kosobudzki
Mariusz Kosobudzki
TSTadeusz Smolnicki
Tadeusz Smolnicki
The paper presents the concept of using generalized durability index of a vehicle limited by fatigue strength, which in literature is called Pseudo Damage Number, as a tool for estimating the impact of driving conditions on the durability of small and medium-sized wheeled vehicles of high mobility. In the case of the Armed Forces, they are the basic means of transport, having a decisive impact on the efficiency of the entire logistics support system of subunits. The determination of the Pseudo Damage Number index provides the basis for estimating the equivalent load amplitude for a given measured road section and the equivalent mileage. The determination of those parameters allows for assessing the influence and significance of real road conditions on the durability of the vehicle by comparing them to previously identified ones. The analysis of the value of the coefficient β characterizing the slope of the curve in the fatigue strength graph was also carried out by referring its value quoted in the literature to the value determined analytically on the selected example.

1 September 2024 in Advances in Science and Technology Research Journal
Verified
Journal Article
Open access
KGKarolina Głowacka
Karolina Głowacka
JMJoanna Małecka
Joanna Małecka
TSTadeusz Smolnicki
Tadeusz Smolnicki
The work analyzes the fracture topography of composite specimens subjected to three-point bending - static and impact. Scanning electron microscopy was used for this purpose. The tests were performed for two different materials - polypropylene and polyamide PA6, each reinforced with...

29 November 2023 in Eksploatacja i Niezawodność – Maintenance and Reliability
Verified
Journal Article
Closed access
TSTadeusz Smolnicki
Tadeusz Smolnicki
PSPiotr Sokolski
Piotr Sokolski
The durability of bearing units of large machines depends mainly on the condition of their welded joints. With this in mind, we developed numerical models of the analyzed bearing units, for which we performed FEM simulations of the stresses in welded joints in several basic load cases. In each of the respective variants the technical condition of the bearing nodes was different and it corresponded to the severity of the degradation processes. Different positions of the superstructure in relation to the undercarriage were also taken into account. The simulations used the hot-spot method dedicated to FEM analyses of complex welded structures. We discovered that the loads have a significant influence on the values and distribution of von Mises principal stresses and their axial components. Based on the carried out analyses, we identified the most unfavorable load cases that generate the highest stresses in the welded joints of the assessed nodes. We also demonstrated that the applied method effectively assesses the stresses of welded joints subjected to variable working loads.