The application of mechanical products in many situations involves linear motion. The cylinder head of an internal combustion engine (ICE), a mechanical product, contains intake and exhaust valves. These valves open or close using the linear motion converted by the camshafts rotated by the engine. A typical engine is operated with a single cam profile; depending on the engine rotation, there are areas where the cam profiles do not match, resulting in a poor engine performance. An intake and exhaust system with an actuator can solve this problem. In a previous study on this system, the geometry and processing during manufacturing were complex. Therefore, in response, a linear actuator operated by Lorentz force with a coil as the mover was designed in this study. Through an electromagnetic field analysis using the finite element method, a three-phase alternating current was applied to the coil, assuming that it would be used as a power source for a general inverter. Consequently, the thrust obtained in the valve-actuation direction was 56.7 N, indicating improved axial thrust over the conventional model.
28 March 2025 in International Journal of Applied Electromagnetics and Mechanics
A continuous steel plate production line in steelworks is several kilometers long, and steel plates suffer from problems, such as vibration, friction, distortion, and surface quality degradation caused by contact with the rollers. To solve this problem, our research group investigated a noncontact guidance control that suppresses the vibration of continuous steel plates by applying an electromagnetic force near the edge of the plates. We experimentally investigated the vibration characteristics of steel plates by varying the positions of the electromagnets used in the magnetic guideway for stationary plates.
Hybrid vehicles utilize multiple power sources, making them energy-efficient and enhancing both fuel efficiency and dynamic performance. As a result, hybrid vehicles have recently been adopted as race cars, which demand high powertrain performance. The hybrid vehicle system comprises two power sources: an internal combustion engine (ICE) and an electric motor, both of which require precise control. Controlling the output of the internal combustion engine is particularly challenging. This study investigated the dynamic response of an actuator in an electronic throttle system. The experimental results demonstrated that optimized parameters significantly improved the dynamic response. As a result, we propose a mechanism for hybrid vehicle performance and report the characteristics of an electronic throttle. The improvement in throttle opening can be verified by adjusting the P term.
In this study, we explored the potential of a compact acoustic control system using giant magnetostrictive actuators (GMAs) for application in ultracompact electric vehicles (EVs), which face significant challenges in maintaining interior acoustic comfort due to their structural limitations. A fundamental investigation was conducted to clarify how differences in the internal structure of GMAs affect their vibration and acoustic output performances. Two GMA prototypes with different internal configurations (Model A, featuring two shorter rods and multiple permanent magnets, and Model B, featuring a single long rod) were evaluated through driving experiments. The acoustic signals were measured using a wall panel setup simulating in-cabin conditions. Both models exhibited an increase in sound pressure level with an increase in the applied voltage. However, the frequency response characteristics differed between the models. Model A performed better in the low-frequency range, whereas Model B maintained consistent performance across a broader frequency range. These findings provide essential insights into the design of space-saving and energy-efficient acoustic systems for next-generation mobility solutions.
20 May 2025 in Journal of Advanced Computational Intelligence and Intelligent Informatics
Ultracompact electric vehicles have compact, lightweight bodies with low outer-plate rigidity. This results in the transmission of road noise from the tires and wind noise (caused by the projection shape of the vehicle) into the cabin. Interior acoustic control systems require devices that can produce sound waves. Next-generation mobility uses giant magnetostrictive actuators (GMAs) for sound production. This is a foundational study for designing GMAs that can be used in such interior acoustic control systems. Magnetostriction forces are generated when a magnetic field deforms giant magnetostrictive materials. The output characteristics were analyzed by electromagnetic-field analysis. Further, the GMA magnetostriction force was analyzed using the finite element method (FEM)—across varying frequency ranges of piezoelectrically controlled amplifiers. The FEM results indicated that the GMA output performance was sufficient to generate sound waves for active noise control in the low-frequency range, 100–500 Hz (road noise). Further optimization is required to expand the frequency range—to accommodate music playback, etc.—including modification of the actuator size, weight, shape, and components and using materials with higher magnetic permeability.
With the widespread use of steer-by-wire in automobiles, research is being conducted on high steering gear ratio systems that reduce the burden on the driver, which enables steering with high sensitivity. However, this decreases the resolution during steering and worsens operability, making steering operation more difficult. In addition, if the amount of steering operation and the magnitude of steering reaction torque are not appropriate for the driver, it may cause operation errors. In a highly sensitive steering system, a small change in steering reaction torque has a large potential to affect the driver. The driver’s steering burden varies depending on conditions, so it is not always possible to reduce the steering burden. Therefore, we evaluated the driver’s steering burden on different days and examined the effect of steering reaction force torque on the steering burden. The results confirmed that the deviation of the burden increases as the load increases.