Pavel Yuryev

Mr. Pavel Yuryev

School of Non-Ferrous Metals, Siberian Federal University, Krasnoyarsk, Krasnoyarskiy Kray, Russia
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 April 2025 in Metals
Verified
Journal Article
Open access
PDF file
BKBoris Kulikov
Boris Kulikov
Evgenii PartykoEvgenii Partyko
Evgenii Partyko
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
PYPavel Yuryev
Pavel Yuryev
YMYulbarskhon Mansurov
Yulbarskhon Mansurov
MBMaksim Baranov
Maksim Baranov
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.

11 December 2024 in Metallurgist
Verified
Journal Article
Closed access
PDF file
IKIgor L. Konstantinov
Igor L. Konstantinov
YBYuriy Baykovskiy
Yuriy Baykovskiy
PYPavel Yuryev
Pavel Yuryev
ABAlexandr I. Bezrukikh
Alexandr I. Bezrukikh
SSSergey B. Sidelnikov
Sergey B. Sidelnikov
DBDmitry Bozhko
Dmitry Bozhko

1 March 2023 in Metallurgist
Verified
Journal Article
Closed access
PDF file
PYPavel Yuryev
Pavel Yuryev
MGM. V. Gerov
M. V. Gerov
IKI. L. Konstantinov
I. L. Konstantinov
VBV. N. Baranov
V. N. Baranov
ABA. I. Bezrukikh
A. I. Bezrukikh
YBYuriy Baykovskiy
Yuriy Baykovskiy

30 November 2022 in Metallurgist
Verified
Journal Article
Closed access
PDF file
VBV. N. Baranov
V. N. Baranov
PYPavel Yuryev
Pavel Yuryev
IKI. L. Konstantinov
I. L. Konstantinov
ABA. I. Bezrukikh
A. I. Bezrukikh
Evgenii PartykoEvgenii Partyko
Evgenii Partyko
AIA. O. Ivanova
A. O. Ivanova

30 June 2023 in Non-ferrous Metals
Verified
Journal Article
Closed access
IKI. L. Konstantinov
I. L. Konstantinov
SSS. B. Sidelnikov
S. B. Sidelnikov
PYPavel Yuryev
Pavel Yuryev
YBYuriy Baykovskiy
Yuriy Baykovskiy
The study of the manufacturability of industrial sheets made of aluminum alloy 1580 for the shape-changing operations of sheet stamping by computer modeling in the DEFORM program with subsequent verification by physical experiment was carried out. Drawing and flanging coefficients, at which it is possible to carry out these operations without cracking, have been established. The results of the research will expand the range of applications of this alloy and will make it possible to obtain parts with rigidity elements from it, which will increase the efficiency of their use. Configurations of such parts can be developed by computer modeling, the reliability of the results of which in this work is confirmed by physical experiments. A study of the manufacturability of semi-finished sheet products made of aluminum alloy 1580 for sheet stamping was carried out. Industrial cold-rolled sheets with a thickness of 1 mm were used as the material. To evaluate the technological effectiveness, we chose such shape-changing operations of sheet stamping as drawing without thinning the wall of the “cup” part type and flanging of the blank in the form of a ring. The first stage was a computer simulation of these operations in the software package DEFORM, which allowed to determine the limiting values of drawing (K) and flanging (Co) coefficients, respectively 1.07 and 1.28, at which the values of the Cockroft-Latham criterion on the surface of virtual blanks did not reach a critical value equal to 1. Physical experiments have shown that drawing with a K coefficient greater than 1.07 leads to crack formation in the junction area of the part wall with its bottom. When flanging with a K0 coefficient of more than 1.28, cracks occurred at the edge of the inner bore of the blank. It was also shown by computer simulation and then confirmed by physical experiment that the use of lubricant during drawing extends the deformability range of the alloy for this operation to a value of K = 1.14. The results of the research will allow to expand the range of application of this alloy and make it possible to produce parts with rigidity elements from it, which will increase the efficiency of their use. Configurations of such parts can be developed by computer modeling, the reliability of the results of which in this work is confirmed by physical experiments. The work was performed by the Laboratory of Low-Carbon Metallurgy and Energy under the state assignment of the FSAEI HE “Siberian Federal University”, a participating organization of the REC “Yenisei Siberia”, as part of the national project “Science and Universities”, project number FSRZ-2021-0010.

30 June 2025 in Non-ferrous Metals
Verified
Journal Article
Closed access
IKI. L. Konstantinov
I. L. Konstantinov
PYPavel Yuryev
Pavel Yuryev
YBYuriy Baykovskiy
Yuriy Baykovskiy
TOT. A. Orelkina
T. A. Orelkina
The structure and properties of an industrial large-size ingot of alloy 1580, obtained by semi-continuous casting, have been studied. Evidence has been presented which indicates that the ingot exhibits a fine crystalline structure and is devoid of primary intermetallides Al3(Sc, Zr). The phase composition of the ingot subsequent to annealing has been ascertained. The present study investigates the modes of hot and cold rolling of the ingot to obtain 1 mm thick sheets. The structure of the resulting sheets, after undergoing the process of annealing, has been shown to represent elongated fibres of grains. These are characterised by the presence of dispersed inclusions of excess phases along their boundaries. It has been established that, upon subjecting sheets to annealing temperatures of 225, 250 and 275 °C, a fibrous structure is observed in the absence of any indications of recrystallisation. However, at an annealing temperature of 300 °C, the presence of single recrystallized grains is detected within the structure. Furthermore, at an annealing temperature of 350 °C, the formation of a recrystallized structure is promoted throughout the volume of the sheet. The graphs presented herein illustrate the dependence of the mechanical properties of annealed cold-rolled sheets on the annealing temperature. The investigation revealed that the plasticity resource of hot-rolled sheets from alloy 1580 is approximately 80% when subjected to cold rolling. The study was supported by the Russian Science Foundation (project № 25-19-20133, https://rscf.ru/project/25-19-20133/), and the Krasnoyarsk Regional Science Foundation.