Aleksandr Kosovich

Mr. Aleksandr Kosovich

School of Non-Ferrous Metals, Siberian Federal University, Krasnoyarsk, Krasnoyarskiy Kray, Russia
orcid
Candidate of Engineering Sciences / Associate Professor / Se...

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 April 2025 in Metals
Verified
Journal Article
Open access
PDF file
BKBoris Kulikov
Boris Kulikov
Evgenii PartykoEvgenii Partyko
Evgenii Partyko
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
PYPavel Yuryev
Pavel Yuryev
YMYulbarskhon Mansurov
Yulbarskhon Mansurov
MBMaksim Baranov
Maksim Baranov
One of the key problems in the billet and shaped casting of aluminum alloys is the presence of various undesirable inclusions and impurities in the melt, which can serve as stress concentrators in the finished product, as well as dissolved hydrogen, which contributes to the formation of porosity. The interaction of aluminum with other gases produced by the combustion of fuel particles, oil, and paint materials brought into the furnace together with charge and scrap increases the amount of nitrides, oxides, carbides, and sulfides in the melt. Flux treatment is widely used as protection of aluminum alloys from oxidation and removal of impurities. The present paper reports the data of a comparative analysis of five widely used flux compositions based on sodium, potassium, and magnesium chlorides. The study covers the following aspects: chemical composition, moisture content, melting temperature and melting range, particle size distribution, and refining ability as measured by the change in Na, Ca, and H2 content after melt treatment.

1 November 2023 in Metallurgist
Verified
Journal Article
Closed access
PDF file
Nikita Andreevich StepanenkoNikita Andreevich Stepanenko
Nikita Andreevich Stepanenko
BKBoris Kulikov
Boris Kulikov
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
SBS. V. Belyaev
S. V. Belyaev
IKI. L. Konstantinov
I. L. Konstantinov
PYPavel Yuryev
Pavel Yuryev

30 July 2021 in Tsvetnye Metally
Verified
Journal Article
Closed access
VBV. N. Baranov
V. N. Baranov
BKB. P. Kulikov
B. P. Kulikov
Evgenii PartykoEvgenii Partyko
Evgenii Partyko
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
Paper presents the laboratory research results about effect of alloying, modifying and fluxing agents, in amount corresponding to consumption standards and used at the RUSAL aluminum smelters, on hydrogen saturation of aluminum melt. In paper the comparison is made between hydrogen measurement results obtained by express analysis of liquid aluminum using an Alu Compact instrument and data of solid aluminum from specialized highly sensitive magnetic mass spectrometer AV-1. As a result of studies, it was found that the maximum of aluminum hydrogen saturation occurs when using powder refining fluxes and alloying agents containing halides of alkali and alkaline earth metals, some of which form crystalline hydrates. It was shown that powder fluxes and alloying agents with flux components contain crystallization and hygroscopic water and, when they are added to melt, increase the concentration of hydrogen in metal by 35-100%. According to the research results, technical solutions are proposed with the aim of reducing the saturation degree of aluminum melt with hydrogen. One of the most effective solutions is to use fused flux lump. The following points were proposed as technical solutions to reduce the saturation degree when alloying, refining, and modifying agents added to melt: make use of fused lump refining and cover-refining fluxes and retreat from powder fluxes; provide incoming control for fluxes and alloying agents containing fluxes; to store fluxes and alloying agents with halides of alkali and alkaline earth metals under conditions that exclude hygroscopic moisture saturation; to increase the consumption of fused refining fluxes by 1.5-2 times during preparation of aluminum-magnesium alloys.The work was performed within the framework of the state assignment for science of the Federal State Autonomous Educational Institution of Higher Education “Siberian Federal University”, project number FSRZ-2020-0013.

14 September 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
SBSergey Vladimirovich Belyaev
Sergey Vladimirovich Belyaev
IGIvan Yurievich Gubanov
Ivan Yurievich Gubanov
YGYuriy Vasilievich Gorokhov
Yuriy Vasilievich Gorokhov
ELElena Mikhailovna Lesiv
Elena Mikhailovna Lesiv
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
EGEvgeniy Alekseevich Goreyavchev
Evgeniy Alekseevich Goreyavchev

18 February 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
YGYuriy Vasilevich Gorokhov
Yuriy Vasilevich Gorokhov
SBSergey Vladimirovich Belyaev
Sergey Vladimirovich Belyaev
ASAleksandr Petrovich Skuratov
Aleksandr Petrovich Skuratov
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
IKIgor Lazarevich Konstantinov
Igor Lazarevich Konstantinov
ASAlexey Sergeevich Strigin
Alexey Sergeevich Strigin

31 October 2022 in Chernye Metally
Verified
Journal Article
Closed access
SAS. L. Arapov
S. L. Arapov
SBS. V. Belyaev
S. V. Belyaev
Aleksandr KosovichAleksandr Kosovich
Aleksandr Kosovich
Evgenii PartykoEvgenii Partyko
Evgenii Partyko
This study is devoted to determining the optimal composition of high-manganese austenitic Hadfield steel for producing castings with increased impact strength and hardness relative to the standard grade. The chemical composition of the steel was modified in terms of expanding the range of Mn content (12–19 %). The effect of combined doping with a complex of elements Cr, Mo, Ni is considered. Preliminary computer modeling and porosity analysis of the cast billets was carried out to determine the place of cutout of representative samples needed to evaluate the actual chemical composition and mechanical properties. Statistical analysis of the obtained results on the content of elements and impact strength of the samples was performed using the desirability function. Further optimization of the model was carried out using the response surface methodology. Based on the analysis of pairwise interactions, two experimental compositions of the Hadfield steel are proposed. A comparison of grade 110G13L with the proposed compositions based on the level of mechanical properties and grain score by microstructure is given. It is concluded that it is promising to further use the proposed Fe–1.1C–16Mn–0.8Si–1.3Cr–Ni–Mo composition, which can improve the reliability of castings operating under conditions of significant wear.The work was carried out within the framework of the state task for science of the Siberian Federal University, project number FSRZ-2020-0013.