Igor Lazarevich Konstantinov

Igor Lazarevich Konstantinov

Auto-generated profile, based on publicly available information

Igor Lazarevich Konstantinov

Siberian Federal University, Krasnoyarsk, Russian Federation

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2020 in Russian Journal of Non-Ferrous Metals
Verified
Journal Article
Closed access
PDF file
IKI. L. Konstantinov
I. L. Konstantinov
VBV. N. Baranov
V. N. Baranov
SSS. B. Sidelnikov
S. B. Sidelnikov
EZE. Yu. Zenkin
E. Yu. Zenkin
PYP. O. Yuryev
P. O. Yuryev
IBI. N. Belokonova
I. N. Belokonova
This article analyzes the processability and properties of sheet products made of a large grade 1580 alloy ingot with a lower scandium content in the

25 December 2019 in Non-ferrous Metals
Verified
Journal Article
Closed access
VBV. N. Baranov
V. N. Baranov
IKI. L. Konstantinov
I. L. Konstantinov
SSS. B. Sidelnikov
S. B. Sidelnikov
EZE. Yu. Zenkin
E. Yu. Zenkin
BJBratsk Rusal Bratsk Aluminium Smelter Jsc
Bratsk Rusal Bratsk Aluminium Smelter Jsc
The study of the cold rolling modes of the plates of aluminum alloy sparingly doped with scandium was performed. As a blank for rolling, a 60 mm thick semifinished rolled stock, obtained at one of the Russian metallurgical enterprises by hot rolling of a 1580 alloy ingot was used. At the first stage of the work, an experimental studies of cold rolling of the plates with different degrees of deformation in the laboratory conditions on a rolling mill DUO 330 with a body of roll of 520 mm long has been implemented to determine the critical value of overall reduction, causing the destruction of samples, which have showed that this value during cold rolling of the hotrolled semifinished material corresponds to 21–22%. At this degree of deformation, the alloy has high strength properties with a sufficiently high plasticity. Further increase in the deformation degree does not lead to a significant growth of strength properties, but can favor to the formation of cracks along the edge of the rolled stock. The hot-rolled semifinished material deformability has been tested in the range of the cold deformation degrees from 10 to 30% using the reduction modes obtained in laboratory conditions at the second stage of the work in order to test the technology of rolling the plates on an industrial mill with a body of roll of 2800 mm long and a billet width of 2000 mm. By the results of mechanical properties testing of the plates rolled with different deformation degrees, it is shown that cold rolling of a hot-rolled billet with deformation degree of 21–22% provides the following mechanical properties of the plates: t = 420 MPa; σ0.2 = 380 MPa; δ = 8%, and further increase of the cold deformation degree leads to an insignificant growth of strength properties (about 10 MPa). This work was carried out under the project 03.G25. 31. 0265 “Development of sparingly alloyed high-strength Al-Sc alloys for use in motor transport and navifation” within the framework of the Program of implementation of complex projects on creation of high-tech production, approved by the Decree No. 218 of the Government of the Russian Federation of April 9, 2010. The article is published as a platform for discussion.

1 January 2024 in Metallurgist
Verified
Journal Article
Closed access
PDF file
SSS. B. Sidelnikov
S. B. Sidelnikov
ELE. S. Lopatina
E. S. Lopatina
IKI. L. Konstantinov
I. L. Konstantinov
DVDenis Sergeevich Voroshilov
Denis Sergeevich Voroshilov
YMYulbarskhon Mansurov
Yulbarskhon Mansurov
ADAlexander Durnopyanov
Alexander Durnopyanov

1 March 2015 in Russian Journal of Non-Ferrous Metals
Verified
Journal Article
Closed access
PDF file
IKI. L. Konstantinov
I. L. Konstantinov
IGI. Yu. Gubanov
I. Yu. Gubanov
IAI. O. Astrashabov
I. O. Astrashabov
SSS. B. Sidel’NIkov
S. B. Sidel’NIkov
NBN. A. Belan
N. A. Belan
The possibility of simulating the actual process of die forging of an AK6 aluminum alloy forged piece using a DEFORM-3D computer program is investigated. The following parameters corresponding to process conditions are introduced: die heating temperature of 350°C, blank heating temperature of 360–470°C, press travel velocity of 5 mm/s, and friction factor (by Siebel) of 0.5. It is shown that computer simulation in the DEFORM-3D program makes it possible to analyze actual processes of die forging of aluminum alloys and to recommend their correction.

1 May 2013 in Russian Journal of Non-Ferrous Metals
Verified
Journal Article
Closed access
PDF file
IKI. L. Konstantinov
I. L. Konstantinov
IGI. Yu. Gubanov
I. Yu. Gubanov
YGYu. V. Gorokhov
Yu. V. Gorokhov
The possibility of simulating the operating procedure for the isothermal forging of a profiled forged piece of an AMg6 aluminum alloy is investigated with DEFORM-3D software. The simulation uses the following boundary conditions. The deformation rate is 10−4-10−3 s−1, deformation resistance is 60 MPa, and the friction factor is 0.1. It is shown that the computational model correctly describes the actual production process for the die isothermal forging, which allows us to recommend this software for designing the production process for obtaining profiled forged pieces made of aluminum alloys.

11 December 2024 in Metallurgist
Verified
Journal Article
Closed access
PDF file
IKIgor L. Konstantinov
Igor L. Konstantinov
YBYuriy Baykovskiy
Yuriy Baykovskiy
PYPavel Yuryev
Pavel Yuryev
ABAlexandr I. Bezrukikh
Alexandr I. Bezrukikh
SSSergey B. Sidelnikov
Sergey B. Sidelnikov
DBDmitry Bozhko
Dmitry Bozhko