This article presents new results on designing alloys with a disordered body‐centered‐cubic (BCC) A2 crystal structure within the refractory high‐entropy alloy (RHEA) system Ta–Mo–Cr–Ti–Al using equilibrium calculations, microstructure analysis, and differential scanning calorimetry (DSC). Thermodynamic calculation utilizing the calculation of the phase diagrams (CALPHAD) method is applied to predict alloy compositions with a dominant disordered A2 phase, which is considered favorable for enhancing room‐temperature ductility. Additionally, the reduced density and improved oxidation resistance are the target properties in the presented alloy design. DSC is used for the identification of the phase transitions taking place upon heating from the room temperature up to 1300 °C. Such phenomena as ordering, phase separation, and higher‐order phase transition occurring in two‐phase BCC RHEAs are discussed based on the results of microstructural characterization, X‐ray diffraction, thermal analysis, and selected area electron diffraction by transmission electron microscopy.
Refractory metal-based Mo-Si-B alloys have long been considered the most promising candidates for replacing nickel-based superalloys in the aerospace and energy sector due to their outstanding mechanical properties and good oxidation of the Mo-silicide phases. In general, the addition of vanadium to Mo-Si-B alloys leads to a significant density reduction, while small amounts of titanium provide additional strengthening without changing the phase evolution within the Moss-Mo3Si-Mo5SiB2 phase field. In this work, high-energy ball milling studies on Mo-40V-9Si-8B, substituting both molybdenum and vanadium with 2 and 5 at. % Ti in all constituents, were performed to evaluate the potential milling parameters and investigate the effects of Ti doping on the milling characteristics and phase formation of these multicomponent alloys. After different milling durations, the powders were analysed with regard to their microstructure, particle size, oxygen concentration and microhardness. After heat treatment, the silicide phases (Mo,V)3Si and (Mo,V)5SiB2 precipitated homogeneously within a (Mo,V) solid solution matrix phase. Thermodynamic phase calculations using the CALPHAD method showed good agreement with the experimental phase compositions after annealing, confirming the stability of the observed microstructure.
Information as concerning the compatibility of EUROFER97, or other martensitic steels, and liquid lead–lithium eutectic is collected and evaluated. The best part addresses dissolution caused by the liquid metal, whereas data on the effect on characteristic mechanical properties of the steel are scarce, and even scarcer for the simultaneous influence of neutron irradiation. The latter must be taken into account for application to thermonuclear fusion, as well as, in case of magnetic confinement of the fusion fuel, the acceleration of EUROFER dissolution in the presence of a magnetic field. A degradation of mechanical properties of the steel caused by the liquid metal manifests itself in a loss of ductility, which requires an incubation period just as the dissolution process in the absence of a mechanical load on the material. As a basis for discussing the dissolution phenomena observed, data on the solubility and diffusivity of the major elements in EUROFER is reviewed and dissolution theory briefly repeated.
The results of modeling the viscosity of fullerene-containing nanofluids (NFs) in a wide temperature range are presented. Two different models for predicting the viscosity of NFs are proposed. The first one is based on the thermodynamic similarity of the studied NFs with their base fluids. It was established that solutions of fullerene ${\mathrm C}_{60}$ in o-xylene as well as solutions of fullerene ${\mathrm C}_{60}$ in tetralin (1,2,3,4 - tetrahydronaphthalene) are thermodynamically similar with o-xylene and tetralin, respectively. To calculate the viscosity of fullerene-containing NFs, the equations based on the activation theory of viscous flow were used. An analysis of the temperature dependence of the activation energy of the base fluids and corresponding NFs was performed. It was found that the temperature dependences of the activation energy of the base fluids and corresponding NFs are practically equidistant lines. That makes possible to predict the viscosity of the NFs using the obtained temperature dependences of the activation energy of the base fluids and limited information on the NF’s viscosity (one experimental value for a certain concentration). The second model for predicting the viscosity of the NFs is based on the information on a free volume that can be obtained from data on the density of the NFs. In this model, it is proposed to use as the free volume of the studied solutions the inverse quantities to their critical amplitudes calculated by the author’s model of the extended scaling.