In this research, four different welding arc modes including conventional cold metal transfer (CMT), CMT-Pulse (CMT-P), CMT-Advanced (CMT-ADV), and CMT pulse advanced (CMT-PADV) were used to deposit 2219-Al wire. The effects of different arc modes on porosity, pore size distribution, microstructure evolution, and mechanical properties were thoroughly investigated. The statistical analysis of the porosity and its size distribution indicated that the CMT-PADV process gave the smallest pore area percentage and pore aspect ratio, and had almost no larger pores. The results from optical microscopy, scanning electron microscopy, and fractographic morphology proved that uniform and fine equiaxed grains, evenly distributed Al₂Cu second phase particles were formed during the CMT-PADV process. Furthermore, the X-ray diffraction test ascertained that the CMT-PADV sample had the smallest lattice parameter and the highest solute Cu content. Besides, the tensile strength could reach 283 MPa, the data scattering was the smallest, and the strength scattering of the sample in the horizontal direction was the shortest. In addition, the strength properties were nearly isotropic, with only 5 MPa difference in the vertical and horizontal directions. The above mentioned results indicated that the mechanical properties of 2219 aluminum alloy was improved using the CMT-PADV arc mode.

The effect of arc modes on the microstructure and tensile properties of 5183 aluminium alloy fabricated by cold metal transfer (CMT) processes has been thoroughly investigated. Heat inputs of CMT processes with three arc modes, i.e., CMT, CMT advance (CMT+A), and CMT pulse (CMT+P), were quantified, and their influence on the formation of pores were investigated. The highest tensile strength was found from samples built by the CMT+A process. This agrees well with their smallest average pore sizes. Average tensile strengths of CMT+A arc mode-built samples were 296.9 MPa and 291.8 MPa along the horizontal and vertical directions, respectively. The difference of tensile strength along the horizontal and vertical directions of the CMT+P and CMT samples was mainly caused by the pores at the interfaces between each deposited layer. The successfully built large 5183 aluminium parts by the CMT+A arc mode further proves that this arc mode is a suitable mode for manufacturing of 5183 aluminium alloy.

This study investigated the anisotropic characteristics of the microstructural, mechanical and corrosion properties of CoCrFeMnNi high-entropy alloy produced by selective laser melting (SLM) additive manufacturing (AM). Under the extremely high thermal gradient during the SLM process, a columnar solidification structure with a single face-centered cubic (FCC) phase structure was formed. The crystal structure exhibited a regular checkerboard structure in the XOY plane (perpendicular to the building direction), which was composed of {110} direction and a small amount of {100} fiber texture. The cellular-dendritic sub-structures formed in the columnar crystal structure with sizes of about 500 nm in diameter. As for the mechanical properties, the XOY plane exhibited higher ultimate tensile strength and yield strength (σ_0.2) but lower elongation to failure compared to the XOZ plane (parallel to building direction), which reflected the anisotropy of the microstructure. The electrochemical test results of the different planes showed that the XOZ plane exhibited better corrosion resistance in comparison with the XOY plane in the 3.5 wt % NaCl solution, which was on account of the selective attack at the Mn-rich inter-cellular regions and the different structures of the cellular-dendritic sub-structures on different planes.

Aiming at handling the contradiction between power constraint of on-orbit manufacturing and the high energy input requirement of metal additive manufacturing (AM), this paper presents an AM process based on small-power metal fine wire feed, which produces thin-wall structures of height-to-width ratio up to 40 with core-forming power only about 50 W. In this process, thermal resistance was introduced to optimize the gradient parameters which greatly reduces the step effect of the typical AM process, succeeded in the surface roughness (Ra) less than 5 μm, comparable with that obtained by selective laser melting (SLM). After a 10 min electrolyte-plasma process, the roughness of the fabricated specimen was further reduced to 0.4 μm, without defects such as pores and cracks observed. The ultimate tensile strength of the specimens measured about 500 MPa, the relative density was 99.37, and the Vickers hardness was homogeneous. The results show that the proposed laser-Joule wire feed-direct metal deposition process (LJWF-DMD) is a very attractive solution for metal AM of high surface quality parts, particularly suitable for rapid prototyping for on-orbit AM in space.

Cf/C-SiC composites have become the preferred material for high-temperature load-bearing applications because of their low density, high strength, and excellent thermal-physical properties. Due to the composite’s poor sintering performance, the sintering temperature and pressure required for the preparation of Cf/C-SiC by traditional methods are also relatively high, which limits its engineering application. Herein, based on the precursor-derived ceramic route and C/C composites material preparation process, a binary binder (coal pitch and polysilylacetylene) is developed, which combines a carbon source, SiC precursor, and semi-ceramic SiC filler organically. Then, the SiC phase was successfully introduced into C/C composites by the slurry impregnation-hot pressing sintering method. The prepared Cf/C-SiC composites showed good mechanical properties, with a density of 1.53 g/cm³ and a bending strength of 339 ± 21 MPa. Moreover, the effects of the binary binder on the microstructure, density, and mechanical properties of Cf/C-SiC composites were investigated. This work provides a novel and effective approach to fabricating Cf/C-SiC composites with low density and high strength.