Copper niobate (CuNb2O6) is an important compound due to its low cost and polymorphism, presenting monoclinic and orthorhombic phases, which leads to unique physical–chemical properties. The electrochemical performance of efficient electrocatalysts for the oxygen evolution reaction (OER) is of importance in order to produce hydrogen gas from water. In this context, this work reports the synthesis of CuNb2O6 particles by high-energy milling for 5 and 10 h, and subsequent thermal treatment at 900 °C for 3 h. The samples were characterized by XRD, XRF, FESEM, RAMAN, UV–Vis, and FT-IR techniques, and were applied as electrocatalysts for the OER. The samples had both monoclinic and orthorhombic crystalline phases. The band gaps were in the range of 1.92 to 2.06 eV. In the application for the OER, the particles obtained by 5 and 10 h of milling exhibited overpotentials of 476 and 347 mV vs. RHE at 10 mA cm−2, respectively. In chronopotentiometry experiments for 15 h, the samples exhibited excellent chemical stability. The electrochemical performance of the sample milled for 10 h showed superior performance (347 mV vs. RHE) when compared with electrocatalysts of the same type, demonstrating that the methodology used to synthesize the samples is promising for energy applications.
Ammonium paratungstate (APT) was synthesized from scheelite ore concentrates from the Brejuí Mine in Currais Novos, Rio Grande do Norte, Northeast Brazil. The process involved acid leaching to obtain tungstic acid (H2WO4), followed by its conversion to APT. A 23 factorial design evaluated the influence of temperature, HCl concentration, and reaction time on the leaching efficiency, revealing temperature and acid concentration as significant variables. Tungsten extraction reached 98.6% under moderate time and temperature conditions. The resulting H2WO4 phase exhibited a lamellar and porous morphology, facilitating its rapid dissolution and crystallization into APT at 60 °C. The produced nanometric APT exhibited high purity, a mixed rod-like/cubic morphology, and thermal stability above 600 °C. This work adds value to the Brazilian tungsten deposits by supporting more efficient and sustainable extraction routes for obtaining APT.
This study presents an integrated low-temperature processing route that converts tungstic acid and ammonium paratungstate derived from scheelite ore (CaWO4) into nanoscale tungsten trioxide (WO3), metallic tungsten (W), and tungsten carbide (WC) via solid-state reaction, hydrogen reduction, and gas–solid reaction, respectively. This approach enables particle size control, reduced energy consumption, and enhanced functional properties, enabling evaluation of the materials’ performance in the oxygen evolution reaction (OER). X-ray diffraction (XRD) confirmed the formation of the desired phases with nanocrystalline structures and average crystallite sizes of 13.3 nm (WO3), 31.55 nm (W), and 10.35 nm (WC). The materials exhibited homogeneous morphologies, demonstrating the effectiveness of the synthesis routes. Electrochemical measurements revealed promising OER activity; the WO3 electrode showed the lowest overpotential of 321 mV at 10 mA cm−2, while W and WC showed 327 mV and 340 mV, respectively, in 1.0 M KOH. Overall, the results demonstrate a strategy for scheelite valorization.
In this work, we present the first report on the synthesis via the sol–gel method of a high-entropy (Fe0.2Co0.2Cu0.2Ni0.2Mn0.2)Nb2O6 with columbite–orthorhombic structure. Polyvinylpyrrolidone (PVP), ammonium niobium oxalate, and equimolar amounts of Fe, Co, Cu, Ni, and Mn ions were used. The refinement of the XRD pattern showed the presence of niobate crystallites with an average size of 48.4 nm and a fraction of 7.6 wt% of a spinel-like phase. At temperatures below 5 K, the DC and AC magnetometry results revealed the presence of a ferromagnetic-like phase due to the niobate phase. The Mössbauer spectrum at 300 K showed a paramagnetic and two magnetically ordered components corresponding to the niobate and the spinel-like phases, respectively. The spectral components were typical of Fe3+, indicating the presence of cation vacancies. The elemental mapping obtained from EDS measurements showed compositional homogeneity. The XRF measurements confirmed a composition consistent with nominal values. These results confirm the feasibility of synthesizing entropy-stabilized columbite oxides via the sol–gel route, opening new opportunities for the design of multifunctional ceramics with tunable structural and magnetic properties for high-performance thermal barrier coatings and energy conversion applications.
This study evaluated the effect of thermal processing in hydrogen (H2) and argon (Ar) atmospheres on the physical and microstructural properties of niobium (Nb) powders for electrolytic capacitors. Nb powders were treated at 750 °C, 850 °C and 950 °C with isothermal holds of 60 min and 120 min—samples H2-850-120 and Ar-850-120 denote the H2 and Ar atmospheres—using a heating rate of 10 °C/min. Powders were compacted at 150 MPa and sintered at 1200 °C under H2. XRD confirmed predominant βH phase and minor NbO in H2-treated powders, while Ar-treated samples exhibited stronger NbO reflections. FEG-SEM micrographs showed finer grains and reduced porosity in H2-850-120. These results demonstrate that hydrogen-atmosphere processing yields Nb powders with improved homogeneity, particle size reduction and densification—key attributes for enhanced capacitor performance.
In this project, a method was developed to synthesize ammoniacal niobium oxalate (NH4)(NbO(C2O4)(H2O)ᵧ)·XH2O, aimed at its application in the preparation of niobium-incorporated materials. This transition metal exhibits excellent properties and is widely available in Brazil. Its versatility makes it essential for metal alloys and electronic components. The synthesis was based on physical and chemical processes, including fusion, decantation, filtration, and complexation, using niobium pentoxide and potassium bisulfate. Rigorous procedures were implemented to ensure precursor quality. Material characterization was performed using X-ray diffraction (XRD), scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and thermogravimetric analysis (TGA), which collectively confirmed the material's morphology, structure, and thermal stability. The results confirmed the efficient synthesis of high-purity niobium oxalate, with the developed method demonstrating technical feasibility by preserving the material's essential physicochemical properties, as verified by the characterization techniques. Key innovations included replacing acid leaching with a more efficient method, implementing neutral-pH decantation instead of traditional acidic processes, and the strategic use of an aqueous acetic acid solution in the washing step. This combination of advancements enabled a 75% reduction in water consumption during the washing stage, thus establishing a significantly more sustainable synthesis protocol for producing this precursor without compromising final product quality.