Maria J. S. Lima

Dr. Maria J. S. Lima


Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2023 in Journal of Physics and Chemistry of Solids
Verified
Journal Article
Closed access
CLCleber da Silva Lourenço
Cleber da Silva Lourenço
RARafael Raimundo Alexandre
Rafael Raimundo Alexandre
RARicardo F. Alves
Ricardo F. Alves
TSThayse R. Silva
Thayse R. Silva
FLFrancisco José Loureiro
Francisco José Loureiro
UGUílame U. Gomes
Uílame U. Gomes

1 August 2021 in Ceramics International
Verified
Journal Article
Closed access
MLMaria J. S. Lima
Maria J. S. Lima
FSFernando E.S. Silva
Fernando E.S. Silva
MSMaria V.M. Souto
Maria V.M. Souto
KAKivia F.G. Araújo
Kivia F.G. Araújo
RMRoberta A.C. Menezes
Roberta A.C. Menezes
UGUílame U. Gomes
Uílame U. Gomes

10 September 2024 in Ceramics International
Verified
Journal Article
Closed access
MLMaria J. S. Lima
Maria J. S. Lima
FSFernando Erick Santos da Silva
Fernando Erick Santos da Silva
RRRafael A. Raimundo
Rafael A. Raimundo
JVJussier de Oliveira Vitoriano
Jussier de Oliveira Vitoriano
CLCleber da Silva Lourenço
Cleber da Silva Lourenço
UGUílame U. Gomes
Uílame U. Gomes

18 May 2017 in Materials Research
Verified
Journal Article
Open access
PDF file
MLMaria J. S. Lima
Maria J. S. Lima
FSFernando Erick Santos da Silva
Fernando Erick Santos da Silva
MSMaria Veronilda Macedo Souto
Maria Veronilda Macedo Souto
MMMeysam Mashhadikarimi
Meysam Mashhadikarimi
ASAriadne Sousa Silva
Ariadne Sousa Silva
CSCarlson Pereira de Souza
Carlson Pereira de Souza
The objective of this work is obtaining W-30 wt% Cu composite powder from ammonium paratungstate hydrated (APT) and hydrated copper nitrate and investigating the influence of some production process parameters of W- 30 wt% Cu in particles form which results in high sinterability and densification of W-30 wt% Cu composite. To achieve this objective, the powder was obtained by manually mixing the APT and copper nitrate and reducing under a hydrogen atmosphere at 800 °C and then compacting at 500 MPa and sintering in a tubular furnace at 1200 °C for 60 minutes. The obtained materials were characterized by XRD, SEM, EDS, particle size analysis, density and microhardness measurements. The composite powder showed a good homogenization of Cu in W with very fine and agglomerated particles and a mean crystallite size of 25.64 nm. SEM coupled with EDS with mapping analysis revealed a homogeneous distribution of Cu and W in the sintered sample. The composite had a relative density of 96.77% and a microhardness of 523.66 HV. Therefore the method of obtaining the composite powder is feasible to sinter W-30 wt% Cu powder due to a greater dispersion and homogenization of phases and the average particle size.

1 January 2015 in Tecnologia em Metalurgia, Materiais e Mineração
Verified
Journal Article
Open access
MLMaria J. S. Lima
Maria J. S. Lima
MSMaria Veronilda Macedo Souto
Maria Veronilda Macedo Souto
ASAriadne Souza Silva
Ariadne Souza Silva
UGUÍLAME U. GOMES
UÍLAME U. GOMES
CSCarlson Pereira de Souza
Carlson Pereira de Souza

13 May 2025 in Ceramics
Verified
Journal Article
Open access
PDF file
KAKívia F. G. Araújo
Kívia F. G. Araújo
CLCleber da Silva Lourenço
Cleber da Silva Lourenço
VSVitor Manoel Silva Fernandes De Souza
Vitor Manoel Silva Fernandes De Souza
MSMatheus Duarte Silva
Matheus Duarte Silva
GVGabriel dos Santos Vasconcelos
Gabriel dos Santos Vasconcelos
UGUÍLAME U. GOMES
UÍLAME U. GOMES
Copper niobate (CuNb2O6) is an important compound due to its low cost and polymorphism, presenting monoclinic and orthorhombic phases, which leads to unique physical–chemical properties. The electrochemical performance of efficient electrocatalysts for the oxygen evolution reaction (OER) is of importance in order to produce hydrogen gas from water. In this context, this work reports the synthesis of CuNb2O6 particles by high-energy milling for 5 and 10 h, and subsequent thermal treatment at 900 °C for 3 h. The samples were characterized by XRD, XRF, FESEM, RAMAN, UV–Vis, and FT-IR techniques, and were applied as electrocatalysts for the OER. The samples had both monoclinic and orthorhombic crystalline phases. The band gaps were in the range of 1.92 to 2.06 eV. In the application for the OER, the particles obtained by 5 and 10 h of milling exhibited overpotentials of 476 and 347 mV vs. RHE at 10 mA cm−2, respectively. In chronopotentiometry experiments for 15 h, the samples exhibited excellent chemical stability. The electrochemical performance of the sample milled for 10 h showed superior performance (347 mV vs. RHE) when compared with electrocatalysts of the same type, demonstrating that the methodology used to synthesize the samples is promising for energy applications.