HaiLong Yao

Dr. HaiLong Yao


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
QHQiang Hu
Qiang Hu
DJDehui Ji
Dehui Ji
Ming-xue ShenMing-xue Shen
Ming-xue Shen
HZHui Zhuang
Hui Zhuang
HaiLong YaoHaiLong Yao
HaiLong Yao
YZYouliang Zhang
Youliang Zhang
Carbide coatings are frequently used to improve the wear resistance of industrial components in various wear environments. In this research, aiming at the service characteristics of easy wear and short service life of ball mill liners, WC–10Cr3C2–12Ni coatings were prepared by supersonic flame spraying technology (HVOF). The reciprocating sliding tests were conducted under four different WC particle size conditions, and the differences in the tribological behavior of the coatings and three–body abrasive wear mechanism were obtained. The findings reveal that the average nanohardness of the WC–Cr3C2–Ni coating is nearly five times greater than that of the steel substance. The COF of tribo-pairs decreases and then increases as the particle size increases. In the case of no particles, the surface of the coating is slightly worn, with fatigue and oxidative wear being the primary wear mechanisms. Small particles (1.5 μm and 4 μm) are crushed and coated on the coating surface, in which the extremely fine particles are plasticized to form friction layers that have a protective effect on the coatings. The protective effect of the particles disappears as the particle size increases and is replaced by a powerful chiseling effect on the coatings, resulting in serious material loss. The particle size has a direct relationship with coating wear.

18 July 2023 in Coatings
Verified
Journal Article
Open access
PDF file
HWHong-Tao Wang
Hong-Tao Wang
FAFenghui An
Fenghui An
XBXiaobo Bai
Xiaobo Bai
HaiLong YaoHaiLong Yao
HaiLong Yao
MZMengxian Zhang
Mengxian Zhang
Ramachandran Chidambaram SeshadriRamachandran Chidambaram Seshadri
Ramachandran Chidambaram Seshadri
Nanograin Fe(Al) solid solution alloy coating was firstly produced through cold-spraying technology using mechanically alloyed powder. Then, the above-mentioned coating was annealed at different temperatures to explore its influence on the phase constitution, microstructure, microhardness and dry sliding wear property of the coatings. Results exhibited that an FeAl phase appeared in the coatings after 500 °C treatment and remained stable with increasing annealing temperature. The annealing temperature had a considerable effect on the microstructure, microhardness and wear behavior of the FeAl coating. The existing laminated structure in the as-sprayed coating gradually faded away with increasing temperature and finally obtained a dense coating microstructure with no particle interface when annealed above 950 °C. Nanograin began to evidently grow at temperatures over 800 °C. The microhardness of the FeAl coating stayed at 400 Hv0.1 at temperatures below 800 °C, then it quickly dropped to 300 Hv0.1 at 950 °C and remained nearly unchangeable up to 1100 °C. The dry sliding wear mechanism of the FeAl coating annealed at low temperatures below 700 °C was mainly delamination of the oxide layer and showed a high wear rate within the order of magnitude range of 10−4, whereas FeAl coatings annealed at high temperatures above 950 °C were worn by microploughing and little oxidation and exhibited very low wear rates within the order of magnitude range of 10−6.

7 June 2021 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
HaiLong YaoHaiLong Yao
HaiLong Yao
JXJing Xia
Jing Xia
DYDeng-Liang Yi
Deng-Liang Yi
CYChao Yang
Chao Yang
MZMeng-Xian Zhang
Meng-Xian Zhang
SLShi-Bin Li
Shi-Bin Li

5 February 2024 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
HaiLong YaoHaiLong Yao
HaiLong Yao
XHXiao-Zhen Hu
Xiao-Zhen Hu
SLShi-Bin Li
Shi-Bin Li
HWHong-Tao Wang
Hong-Tao Wang
XBXiao-Bo Bai
Xiao-Bo Bai
CYChao Yang
Chao Yang

27 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
ZZZhenpeng Zhou
Zhenpeng Zhou
XCxiao chen
xiao chen
XHXiaozhen Hu
Xiaozhen Hu
SLSheng Li
Sheng Li
MLMenglong Lv
Menglong Lv
XBXiaobo Bai
Xiaobo Bai
The influence of post-process heat treatment on cold-sprayed Zn coatings on the Mg alloy substrate was investigated at different temperatures (150, 250, and 350 °C) and times (2, 8, and 16 h). Phase, microstructure, microhardness, and tensile strength of Zn coatings were analyzed before and after heat treatment. Corrosion properties of Zn coatings after heat treatment were investigated in simulated body fluid by using potentiodynamic polarization and immersion testing. Results show that although the heat treatment presented little effect on phase compositions of Zn coatings, the full width at half maxima of the Zn phase decreased with the heat temperature and time. Zn coatings presented comparable microstructures before and after heat treatment in addition to the inter-diffusion layers, and the inter-diffusion layer was dependent on the heat temperature and time. Both the thickness and the microhardness of inter-diffusion layers were increased with the heat temperature and time, with the largest thickness of 704.1 ± 32.4 μm and the largest microhardness of 323.7 ± 104.1 HV0.025 at 350 °C for 2 h. The microhardness of Zn coating was significantly decreased from 70.8 ± 5.6 HV0.025 to 43.9 ± 12.5 HV0.025, with the heat temperature from the ambient temperature to 350 °C, and was slightly decreased with the heat time at 250 °C. Although the tensile strength of Zn coating was slightly increased by heat treatment, with the highest value of 40.9 ± 3.9 MPa at 150 °C for 2 h, excessive heat temperature and time were detrimental to the tensile strength, with the lowest value of 6.6 ± 1.6 MPa at 350 °C for 2 h. The heat temperature and heat time presented limited effects on the corrosion current and corrosion ratio of the Zn coatings, and Zn coatings before and after heat treatment effectively hindered the simulated body fluid from penetrating into the substrate. The corrosion behavior of Zn coatings was discussed in terms of corrosion products and microstructures after immersion.

16 August 2023 in Journal of Thermal Spray Technology
Verified
Journal Article
Closed access
PDF file
ZLZhi-Bin Luo
Zhi-Bin Luo
XHXiao-Zhen Hu
Xiao-Zhen Hu
YXYi-Ting Xie
Yi-Ting Xie
SOShi-Wen Ouyang
Shi-Wen Ouyang
TWTai-Yang Wang
Tai-Yang Wang
CYChao Yang
Chao Yang