Qiang Hu

Qiang Hu


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
QHQiang Hu
Qiang Hu
DJDehui Ji
Dehui Ji
Ming-xue ShenMing-xue Shen
Ming-xue Shen
HZHui Zhuang
Hui Zhuang
HaiLong YaoHaiLong Yao
HaiLong Yao
YZYouliang Zhang
Youliang Zhang
Carbide coatings are frequently used to improve the wear resistance of industrial components in various wear environments. In this research, aiming at the service characteristics of easy wear and short service life of ball mill liners, WC–10Cr3C2–12Ni coatings were prepared by supersonic flame spraying technology (HVOF). The reciprocating sliding tests were conducted under four different WC particle size conditions, and the differences in the tribological behavior of the coatings and three–body abrasive wear mechanism were obtained. The findings reveal that the average nanohardness of the WC–Cr3C2–Ni coating is nearly five times greater than that of the steel substance. The COF of tribo-pairs decreases and then increases as the particle size increases. In the case of no particles, the surface of the coating is slightly worn, with fatigue and oxidative wear being the primary wear mechanisms. Small particles (1.5 μm and 4 μm) are crushed and coated on the coating surface, in which the extremely fine particles are plasticized to form friction layers that have a protective effect on the coatings. The protective effect of the particles disappears as the particle size increases and is replaced by a powerful chiseling effect on the coatings, resulting in serious material loss. The particle size has a direct relationship with coating wear.

7 May 2024 in Tribology Letters
Verified
Journal Article
Closed access
PDF file
DJDe-Hui Ji
De-Hui Ji
LXLi Xiao
Li Xiao
QHQiang Hu
Qiang Hu
SCSiyang Chen
Siyang Chen
QLQiuping Li
Qiuping Li
Ming-xue ShenMing-xue Shen
Ming-xue Shen

21 July 2023 in Metals
Verified
Journal Article
Open access
PDF file
JXJing Xu
Jing Xu
Xiao LiXiao Li
Xiao Li
JXJing Xu
Jing Xu
RFRui Fu
Rui Fu
CYChangjian Yan
Changjian Yan
ZHZhi Hu
Zhi Hu
Immiscible Cu-Fe alloys exhibit poor corrosion resistance due to different corrosion potentials between the constituent phases, which limits their application. In this paper, a composite gradient-structured Cu-10 wt.%Fe plate was prepared via the ultrasonic surface rolling process (USRP). The microstructure evolution, mechanical properties and corrosion behavior were studied. The results demonstrate that USRP effectively enhances both the strength and corrosion resistance of the Cu-10Fe alloy. The improved strength is related to the combined effects of Hall–Petch strengthening, dislocation strengthening, and additional strengthening resulting from homogeneous deformation between the surface layer and the matrix. The enhanced corrosion resistance is primarily attributed to the refined microstructure of the surface layer after USRP, which facilitates the formation of a protective passivation film.

13 November 2023 in Metals
Verified
Journal Article
Open access
PDF file
JXJing Xu
Jing Xu
JXJing Xu
Jing Xu
XZXiaojun Zhao
Xiaojun Zhao
RFRui Fu
Rui Fu
QHQiang Hu
Qiang Hu
CLChaoqiang Liu
Chaoqiang Liu
This study investigates the impact of strain rate on the twinning process (i.e., twin nucleation, twin propagation, and twin growth) and associated mechanical behavior during compression along the normal direction (ND) and transverse direction (TD) of a rolled AZ31 Mg plate at a range of strain rates from 0.00005 s−1 to 2500 s−1. The findings reveal that the yield strength is insensitive to strain rates below 0.05 s−1 during both ND and TD compression tests, while at higher strain rates of 2500 s−1, the yield strength increases under both loading conditions. Interestingly, the TD-compressed sample exhibits a larger yield plateau at a strain rate of 2500 s−1, attributed to an increased activation of {101¯2} twins. Further examination of the microstructure reveals that the twinning process is highly dependent on the strain rate. As the strain rate increases, twin nucleation is promoted, leading to a higher twin boundary density. In contrast, at lower strain rates, twin nucleation is restrained, and the external strain is mainly accommodated by twin growth, which results in higher area fractions of twinned regions.

5 May 2025 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Closed access
PDF file
JWJiahao Wang
Jiahao Wang
XZXueqing Zheng
Xueqing Zheng
QHQiang Hu
Qiang Hu
YXYinan Xu
Yinan Xu
BGBo Guan
Bo Guan
ZYZhiqiang Yi
Zhiqiang Yi

30 November 2022 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
SLShaopeng Liu
Shaopeng Liu
LMLang Mei
Lang Mei
Ming-xue ShenMing-xue Shen
Ming-xue Shen
JXJing Xia
Jing Xia
YXYelong Xiao
Yelong Xiao
QHQiang Hu
Qiang Hu