Gaber Begeš

Prof. Dr. Gaber Begeš

orcid

Research Focus & Metrics

Academic Career Length

25Years (2002-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 October 2009 in Accreditation and Quality Assurance
Verified
Journal Article
Closed access
PDF file
GBGaber Begeš
Gaber Begeš
JDJanko Drnovsek
Janko Drnovsek
LPLeslie R. Pendrill
Leslie R. Pendrill

20 September 2019 in IEEE Industrial Electronics Magazine
Verified
Journal Article
Closed access
BRBlaž Radej
Blaž Radej
GBGaber Begeš
Gaber Begeš
Voltage, temperature, and humidity significantly influence the lifetime of a supercapacitor (SC). Accelerated aging tests are applied to reduce the time required to analyze the influences of these factors. However, accelerated aging has a weakness in that it does not consider the conditions to which the SC is actually exposed when it is installed in a device. This article describes the development of an improved reliability model that simulates the voltage, temperature, and humidity levels that the SC is exposed to during operation in real working conditions. The model has been validated and provides a better lifetime estimation for an SC in a device.

11 March 2002 in Measurement Science and Technology
Verified
Journal Article
Closed access
PDF file
GBGaber Begeš
Gaber Begeš
JDJ Drnovsek
J Drnovsek
IPI Pusnik
I Pusnik
JBJ Bojkovski
J Bojkovski

15 November 2011 in International Journal of Thermophysics
Verified
Journal Article
Closed access
PDF file
GBGaber Begeš
Gaber Begeš

22 February 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Open access
GBGaber Begeš
Gaber Begeš
DADušan Agrež
Dušan Agrež
DHDomen Hudoklin
Domen Hudoklin
This paper presents a method for improving the non-parametric frequency estimation of the fundamental periodicity of a multi-frequency signal when a smaller number of periods are covered - up to two periods in the measurement time. The estimation procedure uses the weights of two Rife-Vincent I windows on the same set of acquired signal samples and then uses a combination of two consecutive DFT amplitude coefficients in the quotient. To reduce the harmonic influence, the technique of near-coherent frequency evaluation is used, and to reduce the interharmonic influence, a method can be added where the rest of the signal is averaged after determining the periodic part of the signal. The simulation and experimental results obtained show a very good compromise between fast and accurate estimation.

6 July 2015 in Meteorological Applications
Verified
Journal Article
Open access
PDF file
GBGaber Begeš
Gaber Begeš
JDJ. Drnovšek
J. Drnovšek
JBJ. Bojkovski
J. Bojkovski
JKJ. Knez
J. Knez
DGD. Groselj
D. Groselj
DHDomen Hudoklin
Domen Hudoklin
The reliability of ground‐based measurements is important in a variety of meteorological areas, such as weather forecasts, air quality and climate. In order to improve this reliability, closer co‐operation with the metrological community has been established. This paper looks at another possible route for improvements, based on carrying out a quality assessment of ground‐based measurements using advanced quality techniques. The quality function deployment (QFD) method was adapted so as to be able to analyse the results of a survey that was conducted among meteorological community. They were asked to analyse the key performance characteristics of typical automatic weather stations (AWSs) systematically with respect to the World Meteorological Organization (WMO) classifications and requirements. The QFD is a well‐known quality tool that connects customer expectations with technical functionalities or engineering characteristics. It makes it possible to prioritize the needs and quantify the results of the assessment. The answers from the survey's questionnaire were used as the input data for the QFD matrix. The findings reveal that the closest correlations are between the customer expectations or attributes and the engineering characteristics, e.g., the validation of the AWSs and the measurement methods, the regular calibration of sensors, and the implementation of automated and manual controls. From the second level of the QFD matrix, it was found that the most important technical solution serving the previously mentioned needs is related to having control over the development and upgrading of the AWSs' software and in terms of an automatic check and the transfer of data to the central database.