This article analyzes two modular power converter concepts, cascaded H-bridges (CHB) and modular multilevel converter (MMC) topologies, with special attention to the latter design. Both concepts have some characteristics in common and can provide the required functionalities for power electronic transformers (PETs). This analysis will cover aspects like the number of required cells, characteristics of the power devices, functionalities, and potential uses.

High-brightness LEDs are considered remarkable lighting devices due to their high reliability, chromatic variety, and increasing efficiency. As a result, a high number of solutions for supplying LED strings are emerging. One-stage solutions are cost-effective, but their efficiency is low because they have to fulfill several purposes with only one converter: power factor correction (PFC), galvanic isolation (in some cases), and current regulation. Two-stage and three-stage solutions have higher efficiency because each stage is optimized for only one or two tasks and they are the preferred options when supplying several strings at the same time. In this paper, a two-stage solution is proposed. The first stage is the well-known PFC boost converter. The second stage, on which this paper is focused, is the asymmetrical half bridge (AHB). Its design has been optimized based on the needs and characteristics of LED-based street lighting applications. The proposed transformer design (with asymmetrical secondary windings) minimizes the conduction losses while the model of the converter during the dead times optimizes their duration, reducing switching losses in the MOSFETs and diodes. Experimental results obtained with a 40-W prototype show an efficiency as high as 94.5% for this second stage and validate the proposed design procedure and model.

Active power-factor correctors (PFCs) are needed to design ac-dc power supplies with universal input voltage range and sinusoidal input current. The classical method to control PFCs consists in two feedback loops and an analog multiplier. Hence, the input current is sinusoidal and it is in-phase with the input voltage. However, a bulk capacitor is needed to balance the input and the output power. Due to its high capacitance, an electrolytic capacitor is traditionally used as a bulk capacitor in PFCs. As a consequence, the lifetime of the ac-dc power supply is limited by the electrolytic capacitor's, which becomes insufficient to some applications (e.g., high-brightness LEDs). This paper proposes a reduction of the output voltage ripple (which allows reduction of the output capacitance) by distorting the input current, but maintaining the harmonic continent compatible with EN 61000-3-2 regulations. The limits of this output capacitor reductions are deduced. Also, a control strategy based on a low-cost microcontroller is developed to put the proposed study into practice. Finally, the theoretical results are validated in a 500-W prototype.

High-brightness light-emitting diodes (LEDs) are considered as a remarkable lighting device due to their high reliability, chromatic variety, and increasing efficiency. As a consequence, a high number of solutions for supplying LED strings are coming out. One-stage solutions are cost effective, but their efficiency is low as they have to fulfill several purposes with only one converter: power factor correction (PFC), galvanic isolation (in some cases), and current regulation. Two-stage and three-stage solutions have higher efficiency as each stage is optimized for just one or two tasks, and they are the preferred option when supplying several strings at the same time. Nevertheless, due to their higher cost in comparison to one-stage solutions, they are used when high efficiency, high performance, and the possibility of supplying several strings are the main concerns. In addition, they are also used when high reliability is needed and electrolytic capacitors cannot be used. In this paper, a three-stage solution and its complete design guideline for LED-based applications is proposed. PFC is achieved by a boost converter, while the galvanic isolation is provided by an electronic transformer (second stage). The third stages (one for each LED string) are designed following the two-input buck schematic, but taking advantage of the load characteristics (i.e., the high value of the LED string knee voltage, approximately equal to half the string nominal voltage). Moreover, a variation of the analog driving technique is also proposed. Experimental results obtained with a 160-W prototype show an efficiency as high as 93% for the whole topology and 95% for the cascade connection of the second and third stages.

Due to their high reliability and luminous efficacy, high-brightness light-emitting diodes are being widely used in lighting applications, and therefore, their power supplies are required to have also high reliability and efficiency. A very common approach for achieving this in ac-dc applications is using a two-stage topology. The power factor corrector boost converter operating in the boundary conduction mode is a very common converter used as first stage. It is normally designed without electrolytic capacitors, improving reliability but also increasing the low-frequency ripple of the output voltage. The asymmetrical half-bridge (AHB) is a perfect option for the second stage as it has very high efficiency, it operates at constant switching frequency, and its output filter is small (i.e., it can be also easily implemented without electrolytic capacitors). Moreover, the AHB is an excellent candidate for self-driven synchronous rectification (SD-SR) as its transformer does not have dead times. However, the standard configuration of the SD-SR must be modified in this case in order to deal with the transformer voltage variations due to the input voltage ripple and, more important, due to the LED dimming state. This modification is presented in this paper. Another important issue regarding the AHB is that its closed-loop controller cannot be very fast and it cannot easily cancel the previously mentioned low-frequency ripple. In this paper, a feed-forward technique, specifically designed to overcome this problem, is also presented. The experimental results obtained with a 60-W topology show that efficiency of the AHB may be very high (94.5%), while the inherent control problems related to the AHB can be overcome by the proposed feed-forward technique.