Pitting corrosion in seawater is one of the most difficult forms of corrosion to identify and control. A workhorse material for marine applications, 316L stainless steel (316L SS) is known to balance resistance to pitting with good mechanical properties. The advent of additive manufacturing (AM), particularly laser powder bed fusion (LPBF), has prompted numerous microstructural and mechanical investigations of LPBF 316L SS; however, the origins of pitting corrosion on as-built surfaces is unknown, despite their utmost importance for certification of LPBF 316L SS prior to fielding. Here, we show that Mn-rich silicate slags are responsible for pitting of the as-built LPBF material in sodium chloride due to their introduction of deleterious defects such as cracks or surface oxide heterogeneities. In addition, we explain how slags are formed in the liquid metal and deposited at the as-built surfaces using high-fidelity melt pool simulations. Our work uncovers how LPBF changes surface oxides due to rapid solidification and high-temperature oxidation, leading to fundamentally different pitting corrosion mechanisms.
We analyze the evolution of subcritical nuclei as a function of nitrogen alloying and thermal annealing in the amorphous phase change material Ge2Sb2Te5. The existence of subcritical nuclei is inferred through measurement of the nucleation time in pulsed laser annealing, and is detected more directly using fluctuation transmission electron microscopy measurements that are sensitive to topological order on the nanoscale. In samples that are pre-annealed before crystallization experiments, the nanoscale order consistently increases and the nucleation times consistently decrease, in agreement with the interpretation that the nanoscale order corresponds to a population of subcritical nuclei that ripens upon annealing. However, this correlation is less obvious in as-deposited samples across a range of nitrogen contents: The quantity of nanoscale order diminishes only slightly with increased nitrogen alloying, whereas the nucleation times increase by nearly two orders of magnitude. We therefore interpret that nitrogen must affect either the critical size in order for a nucleus to be stable (the thermodynamics) or the rate at which nucleation and growth take place (the kinetics).
We investigate the structure of magnetron-sputtered (MS) amorphous silicon (a-Si) prepared under standard deposition conditions and compare this to pure ion-implanted (II) a-Si. The structure of both films is characterized in their as-prepared and thermally annealed states. Significant differences are observed in short- and medium-range order following thermal annealing. Whereas II a-Si undergoes structural relaxation toward a continuous random network, MS a-Si exhibits little change. Cross-sectional transmission electron microscopy reveals the presence of nanopores in the MS film consistent with reduced mass-density. Therefore, the short- and medium-range order of annealed, MS a-Si is tentatively attributed to these pores.
9 September 2014 in Journal of Vacuum Science & Technology A
During the chemical vapor deposition of thin films, a molecular inhibitor can be added to control the morphology during the nucleation stage and/or the conformal coating behavior during the growth stage. The authors use this control strategy to determine the separate influence of nucleation morphology and of conformal growth on the final surface roughness, evaluated through the power spectral density of AFM height data. The experimental system is HfB2 deposition from the precursor Hf(BH4)4 using NH3 as the inhibitor. For a nucleation layer consisting of mounds, the low frequency (long lateral range) roughness cannot be reduced by the overgrowth of film, even with the conformal growth conditions. Conversely, when the nucleation layer consists of a dense compact of islands, the low frequency roughness remains low throughout film growth, even when carried out in the nonconformal growth conditions. In all cases, the high frequency portion of the roughness decays in a similar manner, indicating that short-range smoothing mechanism is operative. The sensitivity of the final surface roughness to the morphology of the initial nucleation layer demonstrates that “shadowing” by peaks in the surface height is a strong kinetic driving force for roughening, consistent with previous theory. The use of an inhibitor molecule in CVD provides a means to obtain ultrasmooth films on relatively unreactive substrates, without the need for surface activation and without changing the film composition.
Fluctuation electron microscopy can reveal the nanoscale order in amorphous materials via the statistical variance in the scattering intensity as a function of position, scattering vector, and resolution. However, several sources of experimental artifacts can seriously affect the magnitude of the variance peaks. The use of a scanning transmission electron microscope for data collection affords a convenient means to check whether artifacts are present. As nanodiffraction patterns are collected in serial, any spatial or temporal dependence of the scattering intensity across the series can easily be detected. We present examples of the major types of artifact and methods to correct the data or to avoid the problem experimentally. We also re-cast the statistical formalism used to identify sources of noise in view of the present results. The present work provides a basis on which to perform fluctuation electron microscopy with a high level of reliability and confidence in the quantitative magnitude of the data.