This study concerns the comparative investigation of two advanced lateral stability automotive controllers with respect to a commercial solution. The research aims to improve the stability performances achieved by a combined tracking of yaw rate and side-slip angle through the application of optimal efforts. The proposed solutions are based on Linear Quadratic Regulation and Sliding Mode Control, respectively. Both rely on the same approach for the control objective definition but differ from the action perspective. This solution involves the adoption of a differential braking actuation technique to deliver a desired yaw moment to the car body to track controlled states. Indeed, a sliding controller can also traction torques of hub-motor configurations as well as steering corrections, achieving vehicle stability and a driving response in accordance with the pilot’s intentions. Calibration and validation of the controllers are performed through a Hardware-in-the-Loop simulation rig, along with a real-time static simulator, performing different close-loop maneuvers to assess achievements in terms of lateral stability. Results show that both solutions ensure higher handling performances if compared to Non-controlled or Commercial-controlled vehicle scenarios.
This study concerns the development and testing of three types of Anti-lock Brake Systems (ABS): a standard on-off wheel’s acceleration control; a wheel’s longitudinal slip controller based on a discrete Proportional-Integral-Derivative (PID) control; and a novel type of ABS that involves controlling the wheel’s speed through a discrete PID. This work was developed inside a wider project that will lead to the implementation of stability control systems in a prototype car. For this reason, the typologies of ABS must not require extra sensors compared to those in standard vehicles: Inertial Measurement Unit (IMU) and 4-wheel speed sensors. Furthermore, they must be easily integrated with other controls and electronic components in terms of sampling time and values. The standard ABS seems more appropriate than the others two because it uses only parameters defined by sensors and it has a simple architecture that does not have the problem of computational time. However, in recent years, cars have been equipped with Electro-Hydraulic-Braking (EHB) units that improve the performance of the system controls. In fact, it is possible to use a control that allows actuators to follow a continuous target and smooth out pressure actions. Even if the longitudinal Slip Controller has a simple architecture and uses a PID control, it is limited to using quantities estimated instead of measured: the tires’ friction coefficient, the tires’ longitudinal stiffness, and the car’s speed. Therefore, the use of a Wheel Speed Controller is the right compromise to link the advantages of both controllers by following the braking pressure continuously and not needing to know the condition and properties of the tires. The results of tests carried out in a Hardware-In-the-Loop (HiL) system are showed and involved a complex vehicle model implemented in real-time.
The aim of this study was to develop trajectory planning that would allow an autonomous racing car to be driven as close as possible to what a driver would do, defining the most appropriate inputs for the current scenario. The search for the optimal trajectory in terms of lap time reduction involves the modeling of all the non-linearities of the vehicle dynamics with the disadvantage of being a time-consuming problem and not being able to be implemented in real-time. However, to improve the vehicle performances, the trajectory needs to be optimized online with the knowledge of the actual vehicle dynamics and path conditions. Therefore, this study involved the development of an architecture that allows an autonomous racing car to have an optimal online trajectory planning and path tracking ensuring professional driver performances. The real-time trajectory optimization can also ensure a possible future implementation in the urban area where obstacles and dynamic scenarios could be faced. It was chosen to implement a local trajectory planning based on the Model Predictive Control(MPC) logic and solved as Linear Programming (LP) by Sequential Convex Programming (SCP). The idea was to achieve a computational cost, 0.1 s, using a point mass vehicle model constrained by experimental definition and approximation of the car’s GG-V, and developing an optimum model-based path tracking to define the driver model that allows A car to follow the trajectory defined by the planner ensuring a signal input every 0.001 s. To validate the algorithm, two types of tests were carried out: a Matlab-Simulink, Vi-Grade co-simulation test, comparing the proposed algorithm with the performance of an offline motion planning, and a real-time simulator test, comparing the proposed algorithm with the performance of a professional driver. The results obtained showed that the computational cost of the optimization algorithm developed is below the limit of 0.1 s, and the architecture showed a reduction of the lap time of about 1 s compared to the offline optimizer and reproducibility of the performance obtained by the driver.
29 March 2022 in SAE International Journal of Advances and Current Practices in Mobility
Current ADAS systems can improve vehicle safety directly influencing its dynamics, reducing the impact of human error while driving. These functionalities have a high impact on the complexity of each unit installed on the car, potentially increasing the development time. In this work, a Hardware in the Loop testing bench and methodology for Autonomous Emergency Braking system is presented, aiming to enable a faster system development process. A commercial production brake by wire unit has been installed on a real-time driving simulator. The AEB functionality of the unit is activable in real-time during the simulation, by the means of a customizable control strategy. Two different AEB controllers have been implemented: the first one reproduces the unit stock functionality, while the second computes the requested deceleration using a PID control strategy. The two controllers have been tested in standardized EuroNCAP Car-to-Car Rear (CCR) collision scenario, implemented on the static simulator. The performances are then compared in terms of time to collision threshold necessary to avoid the impact, deceleration request and jerk, and vehicle-obstacle distance. The proposed methodology highlights the role of the static simulator as a development tool, allowing complete and immersive testing of both hardware and control strategies, greatly reducing the development time.