Esayas Gebreyouhannes Ftwi

Dr. Esayas Gebreyouhannes Ftwi


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 May 2025 in Coatings
Verified
Journal Article
Open access
PDF file
YTYisihak Gebre Tarekegn
Yisihak Gebre Tarekegn
Tom LahmerTom Lahmer
Tom Lahmer
ATAbrham Gebre Tarekegn
Abrham Gebre Tarekegn
EFEsayas Gebreyouhannes Ftwi
Esayas Gebreyouhannes Ftwi
Concrete properties are investigated using intensive physical testing processes that require large amounts of labor and materials that are costly and time-consuming. Properly validated computer models can replace most of the existing physical testing procedures with computer simulations that are relatively quick and inexpensive. Therefore, in this study, the effects of coating thickness and aggregate size on the damping properties of concrete were investigated using numerical simulation with Abaqus/CAE 6.14-1 software. Two different groups of aggregates were used in the simulation, with maximum aggregate sizes of 25 mm and 32 mm. The coating thickness ranged from 0.4 mm to 5.0 mm, using epoxy, silicone, and rubber coatings. The results showed that coatings with smaller aggregate size led to an increase in the damping ratio compared to those with larger aggregate size. Moreover, replacing 20% of coarse aggregates with rubber-coated aggregates results in a damping ratio of 5.75% to 6.21%, reflecting an increase of 22.8% to 32.7%. This variation occurs with coating thicknesses ranging from 0.4 mm to 5.0 mm, with the optimal thickness of 5.0 mm leading to the maximum increase (32.7%) in the damping ratio of concrete.

19 November 2025 in Buildings
Verified
Journal Article
Open access
PDF file
YTYisihak Gebre Tarekegn
Yisihak Gebre Tarekegn
Tom LahmerTom Lahmer
Tom Lahmer
ATAbrham Gebre Tarekegn
Abrham Gebre Tarekegn
EFEsayas Gebreyouhannes Ftwi
Esayas Gebreyouhannes Ftwi
Rubber chips, when used as a partial replacement for coarse aggregates in concrete, tend to increase ductility, absorb energy, and can be beneficial due to their ability to reduce impact forces and dampen vibrations. However, they lead to a substantial decrease in compressive strength compared to ordinary concrete. Due to the weak bond between rubber particles and the concrete matrix, sand-coating surface treatment was applied to enhance the interfacial properties of the rubber surface. In this research, a detailed numerical analysis was conducted in order to predict the mechanical and dynamic behavior of concrete by incorporating partially replaced coarse aggregates with uncoated and sand-coated rubber chips. The study also seeks to examine the effects of rubber inclusion on key parameters such as damping ratio and compressive strength, thereby providing insights into the effectiveness of using recycled rubber as a sustainable alternative material in concrete production. The compressive strength and damping ratio of concrete were examined through a three-dimensional numerical simulation using ABAQUS/CAE 6.14-1. The results demonstrated that the optimal compressive strength was achieved with a 15% sand-coated rubber replacement, resulting in a 15.67% increment. Furthermore, the maximum improvements in damping ratios were observed to be 48.42% for uncoated rubber chips and 25% for coated ones, when compared to conventional concrete. These enhancements highlight the potential of both coated and uncoated rubber inclusions, due to rubber’s high elasticity. Moreover, at optimized levels, improved concrete properties can be achieved while promoting sustainability through material reuse.

1 January 2023 in International Journal of Engineering and Applied Sciences
Verified
Journal Article
Open access
PDF file
YTYisihak Gebre Tarekegn
Yisihak Gebre Tarekegn
Tom LahmerTom Lahmer
Tom Lahmer
MMMatthias Muller
Matthias Muller
ATAbrham Gebre Tarekegn
Abrham Gebre Tarekegn
EFEsayas Gebreyouhannes Ftwi
Esayas Gebreyouhannes Ftwi
Concrete structures may be subjected to dynamic loadings like earthquakes, impact, and vehicular loads. These loads may cause considerable damage to infrastructures and shorten their life span. To reduce the effects, improving concrete’s dynamic properties is important. This can be done using granular elastic components and fibers in the production of concrete. This research explores the influence of using coated aggregates on the physical, mechanical, and dynamic properties of concrete. Experimental investigation on concrete with epoxy, epoxy-sand, and epoxy-crumb rubber as a partial replacement of coarse aggregates at different volume fractions ranging from 5% to 20% was conducted. Furthermore, the dynamic modulus of elasticity of concrete with coated aggregate was determined by measuring the resonant frequencies of flexural vibrations in a prismatic beam using an impactor (hammer). Results indicate that partial replacement of epoxy-crumb rubber coated aggregates in concrete shows a reduction in mechanical proprieties. However, significant improvements in the mechanical and dynamic properties of concrete were observed by the partial replacement of coarse aggregates with epoxy and epoxy-sand coated aggregates. Compressive strength and dynamic elastic modulus were enhanced by 12% and 10%, respectively, when concrete with 15% epoxy-sand coated was used. The results showed that concrete specimens using epoxy and epoxy-sand coated as a partial replacement for coarse aggregate have higher mechanical properties as compared to those of concrete specimens with epoxy-crumb rubber-coated aggregates. Moreover, the results showed that the calculated values of the dynamic modulus of concrete using the empirical relations proposed by Popovics and Hansen were overestimated as compared to the experimental values.

20 March 2026 in European Journal of Materials Science and Engineering
Verified
Journal Article
Closed access
USUmer Sadik
Umer Sadik
EFEsayas Gebreyouhannes Ftwi
Esayas Gebreyouhannes Ftwi
This research investigated the effect of aggregate size on the bond strength of cast-in-place (CI) and post-installed (PI) reinforcement bars on 112 specimens (60 CI and 52 PI) under a pull-out test. The PI reinforcements were inserted to center of the concrete specimen using FIS EM plus 390 S epoxy mortar. Different coarse aggregate sizes (4.75 mm, 12.5 mm, 25 mm and 37.5 mm) were considered to study the influence of aggregate size. Reinforcement bars with diameters of 8 mm, 10 mm, and 12 mm were used. The experimental result showed that the influence of aggregate size on the bond strength of CI specimens with smaller bar diameters (8 mm and 12 mm) is insignificant. In the post-peak range, the residual bond of CI specimens with larger aggregate size is greater than that of CI samples with smaller aggregate size. All PI specimens failed in rebar rupture mode, regardless of the bar diameter, embedment length (even with a smaller embedment length of 5 times the diameter of the bar), aggregate size, and drilling technique. The epoxy mortar used was effective, enabling the utilization of 100% of the reinforcement bar capacity. Splitting failure mode was not observed in PI specimens, which is a good implication for the effectiveness of PI bars. In addition, comparisons between experimental and analytical models from codes and researchers were made, and it was found that the experimental results of the current study for CI specimens are in good agreement with the CEB-FIP 2010 model code predictions.

1 August 2026 in Engineering Research Express
Verified
Journal Article
Closed access
SUSadik M Umer
Sadik M Umer
EFEsayas Gebreyouhannes Ftwi
Esayas Gebreyouhannes Ftwi
Beam–column joints (BCJs) are key components of reinforced concrete (RC) moment-resisting frame structures subjected to seismic loading to ensure integrity and overall stability. Many past earthquakes have highlighted the vulnerability of BCJs in non-seismically designed (NSD) RC moment-resisting frame structures. Typically, exterior BCJs are more susceptible to seismic action than interior BCJs owing to the inherent confinement of interior BCJ. This study investigates the possibility of seismic strengthening of exterior RC BCJ using post-installed reinforcement. These reinforcements may act as joint transverse reinforcements. Eight specimens were investigated, where three were CSs, the other three were strengthened specimens with bent-in bottom beam bars, one was strengthened with straight bottom beam reinforcement, and the last one evaluated the post-damage performance of a joint strengthened with bent-in bottom beam bars. The results show that there is a capacity increment of 14%–44% in the upward direction and 15.9%–72% in the downward direction. In addition to capacity enhancement, restraining side (edge) concrete cover spalling and altering the mode of failure from joint shear failure to combined beam reinforcement yielding (which is the onset of the formation of beam hinge) and joint shear failure mode were observed from the strengthened specimens. This significant improvement and finding show that the proposed strengthening technique is promising for enhancing the seismic performance of NSD BCJs.