Post-tensioning (PT), a method of pre-stressing, involves the use of high-strength steel strands/tendons to reinforce concrete or other materials. On the contrary, carbon fiber-reinforced polymers (CFRPs) are lightweight, high-strength materials with used to strengthen concrete structures by adhering the polymer to the concrete element. Challenges with post-tensioned elements include reverse curvature of the PT strands, tendon misplacement, and frequent damage in the anchorage and dead-end zones. These difficulties frequently cause bulging of the surrounding concrete, even at lower stress levels, and can lead to concrete bursting when tension exceeds certain threshold. This study investigates into the potential of CFRP strengthening technique to improve the flexural capacity of post-tensioned concrete beams with anchorage loss. Through an experimental program, the study compares the performance of control beams to those reinforced with different layers of CFRP. The results of this study demonstrated that there was a significant increase in flexural capacity, ranging from 45.31% to 78.62% for single layers and 87.17% to 153% for double layers of CFRP sheet. Additionally, the research examines how different levels of prestressing and CFRP wraps influence crack formation and delamination patterns of carbon fiber, with promising results. It was also noted that optimal usage of CFRP fibers and tendons is found to be critical. The study suggests exploring alternative fiber types and orientations for future study.
Concrete properties are investigated using intensive physical testing processes that require large amounts of labor and materials that are costly and time-consuming. Properly validated computer models can replace most of the existing physical testing procedures with computer simulations that are relatively quick and inexpensive. Therefore, in this study, the effects of coating thickness and aggregate size on the damping properties of concrete were investigated using numerical simulation with Abaqus/CAE 6.14-1 software. Two different groups of aggregates were used in the simulation, with maximum aggregate sizes of 25 mm and 32 mm. The coating thickness ranged from 0.4 mm to 5.0 mm, using epoxy, silicone, and rubber coatings. The results showed that coatings with smaller aggregate size led to an increase in the damping ratio compared to those with larger aggregate size. Moreover, replacing 20% of coarse aggregates with rubber-coated aggregates results in a damping ratio of 5.75% to 6.21%, reflecting an increase of 22.8% to 32.7%. This variation occurs with coating thicknesses ranging from 0.4 mm to 5.0 mm, with the optimal thickness of 5.0 mm leading to the maximum increase (32.7%) in the damping ratio of concrete.
Rubber chips, when used as a partial replacement for coarse aggregates in concrete, tend to increase ductility, absorb energy, and can be beneficial due to their ability to reduce impact forces and dampen vibrations. However, they lead to a substantial decrease in compressive strength compared to ordinary concrete. Due to the weak bond between rubber particles and the concrete matrix, sand-coating surface treatment was applied to enhance the interfacial properties of the rubber surface. In this research, a detailed numerical analysis was conducted in order to predict the mechanical and dynamic behavior of concrete by incorporating partially replaced coarse aggregates with uncoated and sand-coated rubber chips. The study also seeks to examine the effects of rubber inclusion on key parameters such as damping ratio and compressive strength, thereby providing insights into the effectiveness of using recycled rubber as a sustainable alternative material in concrete production. The compressive strength and damping ratio of concrete were examined through a three-dimensional numerical simulation using ABAQUS/CAE 6.14-1. The results demonstrated that the optimal compressive strength was achieved with a 15% sand-coated rubber replacement, resulting in a 15.67% increment. Furthermore, the maximum improvements in damping ratios were observed to be 48.42% for uncoated rubber chips and 25% for coated ones, when compared to conventional concrete. These enhancements highlight the potential of both coated and uncoated rubber inclusions, due to rubber’s high elasticity. Moreover, at optimized levels, improved concrete properties can be achieved while promoting sustainability through material reuse.
1 January 2023 in International Journal of Engineering and Applied Sciences
Concrete structures may be subjected to dynamic loadings like earthquakes, impact, and vehicular loads. These loads may cause considerable damage to infrastructures and shorten their life span. To reduce the effects, improving concrete’s dynamic properties is important. This can be done using granular elastic components and fibers in the production of concrete. This research explores the influence of using coated aggregates on the physical, mechanical, and dynamic properties of concrete. Experimental investigation on concrete with epoxy, epoxy-sand, and epoxy-crumb rubber as a partial replacement of coarse aggregates at different volume fractions ranging from 5% to 20% was conducted. Furthermore, the dynamic modulus of elasticity of concrete with coated aggregate was determined by measuring the resonant frequencies of flexural vibrations in a prismatic beam using an impactor (hammer). Results indicate that partial replacement of epoxy-crumb rubber coated aggregates in concrete shows a reduction in mechanical proprieties. However, significant improvements in the mechanical and dynamic properties of concrete were observed by the partial replacement of coarse aggregates with epoxy and epoxy-sand coated aggregates. Compressive strength and dynamic elastic modulus were enhanced by 12% and 10%, respectively, when concrete with 15% epoxy-sand coated was used. The results showed that concrete specimens using epoxy and epoxy-sand coated as a partial replacement for coarse aggregate have higher mechanical properties as compared to those of concrete specimens with epoxy-crumb rubber-coated aggregates. Moreover, the results showed that the calculated values of the dynamic modulus of concrete using the empirical relations proposed by Popovics and Hansen were overestimated as compared to the experimental values.
This research investigates the dynamic response of three-dimensional concrete beams with coated aggregates subjected to transient wave propagation induced by piezoelectric actuators (PZT-lead zirconate titanate). The aim was to assess the effects of coated aggregates on concrete’s damping behavior and wave attenuation. The effect of various coating materials (epoxy and rubber) and replacement levels ranging from 5% to 25% by volume of the natural coarse aggregates on wave attenuation and energy dissipation were investigated through Finite Element Modeling (FEM) using Abaqus/CAE 6.14-1 software. Moreover, the effect of coating thickness is investigated for thicknesses ranging from 1.0 mm to 3.5 mm. The findings show that the replacement level, coating thickness, and coating material have a major effect on damping characteristics of concrete. It was also observed that rubber-coated aggregates with a 3.0 mm coating thickness (20% replacement level) exhibited an optimal damping ratio of 6.15%, representing a 29.5% increase, and offer enhanced energy dissipation, better damping performance, and the ability to alter wave travel paths, all of which could be advantageous for Structural Health Monitoring (SHM) applications. In line with this, the damping ratio of concrete beam models with epoxy- and rubber-coated aggregates, embedded with PZT material, was significantly higher (by approximately 1% to 18%) compared to that of the concrete model without PZT materials. Additionally, the findings showed that the concrete’s damping properties were greatly impacted by the interaction between PZT materials and coated aggregates. All things considered, the dynamic response and damping performance of concrete with coated-aggregate surface properties were successfully assessed using PZT-based simulations.
5 December 2024 in International Journal of Engineering and Applied Sciences
This paper presents a case study focused on the deterministic and probabilistic structural assessments of a cracked reinforced concrete (RC) slab and evaluation using in-situ load testing. The case study explores the practical application of in-situ load testing as a diagnostic tool for evaluating the condition of the slab and determining its ultimate load-carrying capacity in the presence of cracks, and service loads are used to verify its serviceability. Through comprehensive analysis and interpretation of test results, this study aims to provide valuable insights into the structural performance of cracked reinforced concrete slabs and inform effective repair and rehabilitation strategies. The building under examination is a G+4 reinforced concrete structure constructed using ready mix concrete transported to the construction site. Upon inspecting the slab, which had a total thickness of 170 mm, numerous deeply mapped cracks were evident, visible from the slab's surface and extending through its entire depth. Structural analysis indicated that the design included sufficient reinforcement and that the loads acting upon the slab were not expected to induce the cracking. Factors such as poor construction practices, potential issues with the cement used, and excessive evaporation may have contributed to the occurrence of these cracks, necessitating repairs. A full-scale in-situ load test was performed following ACI 318-08 testing procedures and results show that the slab under investigation is reasonably safe against serviceability and strength requirements with “no evidence” of failure.