Muhammad Khafidh

Dr. Muhammad Khafidh

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 June 2023 in Polymers
Verified
Journal Article
Open access
PDF file
AIA.P. Irawan
A.P. Irawan
DFD.F. Fitriyana
D.F. Fitriyana
Januar Parlaungan SiregarJanuar Parlaungan Siregar
Januar Parlaungan Siregar
CTC. Tezara
C. Tezara
PAPaula Tjatoerwidya Anggarina
Paula Tjatoerwidya Anggarina
RYRahmadi Yotenka
Rahmadi Yotenka
Brake friction materials (BFMs) have a critical role in ensuring the safety as well as the reliability of automotive braking systems. However, traditional BFMs, typically made from asbestos, are associated with environmental and health concerns. Therefore, this results in a growing interest in developing alternative BFMs that are eco-friendly, sustainable, and cost-effective. This study investigates the effect of varying concentrations of epoxy, rice husk, alumina (Al2O3), and iron oxide (Fe2O3) on the mechanical and thermal properties of BFMs prepared using the hand layup method. In this study, the rice husk, Al2O3, and Fe2O3 were filtered through a 200-mesh sieve. Note that the BFMs were fabricated using different combinations and concentrations of the materials. Their mechanical properties, such as density, hardness, flexural strength, wear resistance, and thermal properties, were investigated. The results suggest that the concentrations of the ingredients significantly influence the mechanical and thermal properties of the BFMs. A specimen made from epoxy, rice husk, Al2O3, and Fe2O3 with concentrations of 50 wt.%, 20 wt.%, 15 wt.%, and 15 wt.%, respectively, produced the best properties for BFMs. On the other hand, the density, hardness, flexural strength, flexural modulus, and wear rate values of this specimen were 1.23 g/cm3, 81.2 Vickers (HV), 57.24 MPa, 4.08 GPa, and 8.665 × 10−7 mm2/kg. In addition, this specimen had better thermal properties than the other specimens. These findings provide valuable insights into developing eco-friendly and sustainable BFMs with suitable performance for automotive applications.

1 June 2019 in Wear
Verified
Journal Article
Closed access
MKMuhammad Khafidh
Muhammad Khafidh
DSD.J. Schipper
D.J. Schipper
MMM.A. Masen
M.A. Masen
NVN. Vleugels
N. Vleugels
WDW.K. Dierkes
W.K. Dierkes
JNJ.W.M. Noordermeer
J.W.M. Noordermeer

18 May 2023 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
MKMuhammad Khafidh
Muhammad Khafidh
FPFinny Pratama Putera
Finny Pratama Putera
RYRahmadi Yotenka
Rahmadi Yotenka
DFD.F. Fitriyana
D.F. Fitriyana
RWRahmat Doni Widodo
Rahmat Doni Widodo
NINur Hidayah Ismail
Nur Hidayah Ismail
The use of composite materials in brake pads is becoming increasingly popular due to their high-performance characteristics, including good thermal stability, high wear resistance, and low noise generation. However, the development of new composite materials that offer even better performance is still an ongoing research area. In this study, the composite was made by hand layup method using epoxy resin as matrix material, with rice husk, Al2O3, and Fe2O3 as reinforcing materials. The composition of the composites was varied by changing the percentage of the reinforcement materials. The composites were then subjected to several characterization tests, including density, hardness, flexural strength, thermal analysis, Scanning Electron Microscopy (SEM), TGA/DSC, and wear testing. The test results showed that additional reinforcement materials to the epoxy resin matrix improved the mechanical properties of the composites. Overall, the study demonstrates that a hand layup method is a viable approach for preparing brake pad composite materials and that the addition of rice husk, Al2O3, and Fe2O3 can improve the mechanical properties of the composites. The best properties produced in this research were found in one of the specimens which used epoxy, rice husk, Al2O3, and Fe2O3 with a composition of 50 wt.%, 20 wt.%, 15 wt.%, and 15 wt.%. However, the addition of rice husk also provides wear resistance and thermal stability. This study contributes to the Sustainable Development Goals (SDGs) by advancing innovation, promoting sustainability, and reducing emissions in automotive industry applications.

20 July 2018 in Wear
Verified
Journal Article
Open access
MKMuhammad Khafidh
Muhammad Khafidh
BSB. Setiyana
B. Setiyana
JJJ. Jamari
J. Jamari
MMM.A. Masen
M.A. Masen
DSD.J. Schipper
D.J. Schipper
Elastomeric materials are used in daily applications, such as tires and conveyor belts. Sliding friction of elastomeric materials often produces a unique periodic wear pattern. In general, the periodic wear pattern has to be prevented because it generates surface instabilities and, as a result, vibration. Sliding contact between an elastomer and a rigid ball may cause the development of a periodic wear pattern like a wave on the elastomer surface, called a wavy wear track. The present study has investigated the occurrence of the wavy wear track on the elastomers under several operating conditions. The elastomers used were a Styrene-Butadiene Rubber (SBR) and Butadiene Rubber (BR) reinforced with two types of fillers, i.e., highly dispersible silica and short-cut aramid fiber. A pin-on-disc tribometer was used to study the wavy wear track of the materials under several operating conditions. An analytical model was used to predict the wave length of the wear pattern and to study the occurrence of the wavy wear track. The results show that the occurrence of the wavy wear track depends on the mechanical properties of the elastomer, the operating conditions (such as sliding velocity and force), the inertia mass of the counter surface frame and the circumferential length of the wear track. The analytical model is in good agreement with the experimental results.

29 January 2019 in Tribology Letters
Verified
Journal Article
Open access
PDF file
MKMuhammad Khafidh
Muhammad Khafidh
DSD. J. Schipper
D. J. Schipper
MMM. A. Masen
M. A. Masen
Surface modification of an elastomer may be formed during sliding contact with a rigid counter surface. This alteration leads to a change of mechanical properties at the surface and as a result a change in frictional behavior. Therefore, investigations related to the formation of a modified surface layer on elastomers and its effect on friction are of importance. In the present study, the formation of a modified surface layer on elastomer reinforced by silica is studied. Sliding friction is performed using a pin-on-disc tribometer. Several parameters are varied, namely contact pressure, velocity, and roughness of the counter surface. The existence of a modified surface layer is investigated by using a scanning electron microscope. The results show that the existence of a modified surface layer depends on the competition between the formation rate of the layer and the wear rate. The formation of the layer depends on the contact pressure, velocity, and sliding distance. A general formulation to calculate the volume of formation is proposed. Furthermore, a map of the formation of a modified surface layer is developed.

1 June 2018 in Journal of Mechanical Engineering and Sciences
Verified
Journal Article
Open access
MKMuhammad Khafidh
Muhammad Khafidh
DSD.J. Schipper
D.J. Schipper
MMM.A. Masen
M.A. Masen
VVV. Vleugels
V. Vleugels
JNJ.W.M. Noordermeer
J.W.M. Noordermeer
Elastomeric materials are widely used in daily applications, such as conveyor belts and wiper. Generally, elastomeric materials show poor tribological behavior. Adding fibers to an elastomer is a way to solve this problem. The orientation of the fibers influences the mechanical and tribological behavior of the elastomers. In the present study, the effect of short-cut aramid fiber orientation on the tribological behavior for a Styrene-Butadiene Rubber (SBR) was examined. Three types of compounds which have different fiber orientations were prepared, resulting in normal, transverse and longitudinal orientation to the sliding direction. A contact model of the viscoelastic-anisotropic behaving elastomer was used to calculate the contact area. The friction and wear of the compounds were evaluated using a pin-on-disc tribometer. The results show that the frictional shear stresses of all compounds are nearly the same due to the presence of fibers on the wear track. The normal orientation of fibers shows the mostv effective way to increase the wear resistance compared to the longitudinal and transverse orientation of the fibers.