The combination of electrocoagulation (EC) with complementary treatment methods has garnered increasing attention for wastewater remediation. This study aims to design and optimize a hybrid electrocoagulation–adsorption (EC/Ads) process for the removal of ketoprofen (KTP) from aqueous solutions. The adsorption of KTP onto activated carbon (AC) alone exhibited a low removal efficiency of approximately 27% under the following conditions: initial KTP concentration ([KTP]0) = 23 mg·L−1, pH = 6, adsorbent dose (qAC) = 0.5 g, and contact time = 30 min. In contrast, the EC process alone achieved a removal efficiency of 59.69% under similar conditions (current density (i) = 18.6 mA·cm−2, NaCl = 3.5 g·L−1). The combined EC/Ads process significantly enhanced KTP removal, reaching 87.11% under the same operational parameters. The synergistic effect of the combined treatment was quantified with a synergy index of 1.37. Characterization techniques included FTIR analysis of both AC and KTP, as well as adsorption–desorption isotherms and pHPZC determination for AC. To further optimize the EC/Ads process, a response surface methodology based on central composite design (CCD) was applied to assess the influence of four independent variables: pH, [KTP]0, current density, and qAC. Optimal conditions were identified as follows: qAC = 0.63–0.99 g, i = 12.32–14.68 mA·cm−2, pH = 6.5, and [KTP]0 = 22.5 mg·L−1; these conditions resulted in 100% KTP removal after 30 min of treatment. These findings demonstrate the potential of the EC/Ads hybrid process to be an efficient and sustainable alternative for pharmaceutical contaminant removal.
Bentonite-supported iron catalysts (Bent-Fe) were synthesized and investigated for their application in the heterogeneous electro-Fenton process for amoxicillin (AMX) degradation. The synthesized catalyst was thoroughly characterized using BET, XRD and SEM-EDS analyses, which confirmed the successful incorporation and homogeneous distribution of iron within the bentonite matrix. Acid activation significantly increased the specific surface area from 32 to 216 m2 g−1, while subsequent iron impregnation reduced it to 152 m2 g−1, indicating effective iron immobilization within the porous structure. High-resolution XPS analysis of Bent-Fe indicates that the Fe(III) is embedded within the bentonite matrix. These results confirm the successful formation of the Fe(III)-bentonite catalyst, in which both components retain their structural integrity. Adsorption experiments showed that AMX adsorption onto Bent-Fe was negligible over the investigated pH range. Despite this limited adsorption, the electro-Fenton/Bent-Fe system exhibited high degradation efficiencies reaching 95% at pH 3 and 91% at pH 6 after 120 min of electrolysis. These degradation rates corresponded to chemical oxygen demand (COD) removals of 55% and 39%, respectively. The comparable performance near-neutral pH conditions demonstrates the feasibility of operating the heterogeneous electro-Fenton process at near-neutral pH conditions, highlighting the effectiveness of bentonite as a support material for iron stabilization and catalytic degradation of AMX.
The adsorptive removal of tetracycline (TC) in aqueous solution, a widely used antibiotic, was investigated using activated carbon derived from cotton textile waste. The valorization of textile waste provides a sustainable strategy that not only reduces the growing accumulation of discarded textiles but also supports a circular economy by transforming waste into efficient adsorbent materials for the removal pharmaceutical contaminants. This dual environmental and economic benefit underscores the novelty and significance of using cotton-based activated carbons in wastewater treatment. In this study, cotton textile waste was utilized as a raw material for the preparation of adsorbents via pyrolysis under nitrogen at 600 °C followed by chemical modification with H2SO4 solutions (1, 2, and 3 M). The sulfuric-acid modified-carbons (SMCs) were characterized by BET surface area analysis, FTIR spectroscopy and SEM imaging. Batch adsorption experiments were carried out to evaluate the effects of key operational parameters including contact time, initial TC concentration and solution pH. The results showed that the material treated with 2 M H2SO4 displayed the highest adsorption performance, with a specific surface area of 700 m2/g and a pore volume of 0.352 m3/g. The pH has a great influence on TC adsorption; the adsorbed amount increases with the initial TC concentration from 5 to 100 mg/L and the maximum adsorption capacity (74.02 mg/g) is obtained at pH = 3.8. The adsorption behavior was best described by Freundlich isotherm and pseudo-second-order kinetic models. This study demonstrates that low-cost and abundantly available material, such as cotton textile waste, can be effectively repurposed effective adsorbents for the removal of pharmaceutical pollutants from aqueous media.
This study investigates the degradation and mineralization of sulfamethazine (SMT) by an electrochemically assisted Fe3+/persulfate (electro/Fe3+/PDS) process. Experiments were conducted in a single-compartment electrochemical cell equipped with a carbon felt anode and a stainless steel cathode under constant current conditions. Compared with PDS alone and Fe3+/PDS, the combined electro/Fe3+/PDS system exhibited a strong synergistic effect, achieving up to 89.4% SMT removal within 90 min at a current intensity of 1.6 A. The enhanced performance was attributed to electrochemical Fe2+ regeneration enabling continuous activation of persulfate and generation of sulfate radicals (SO4•−). Operational parameters significantly influenced process efficiency. Increasing current intensity accelerated SMT degradation but reduced mineralization efficiency due to parasitic reactions. Under optimized conditions (I = 3 A and [Fe3+] = 1 mM), SMT degradation reached 96.83% after 60 min, while the mineralization yield attained 72.05%. Excess iron promoted radical scavenging. Similarly, a PDS concentration of 5 mM was sufficient, with higher dosages leading to self-scavenging effects. Kinetic analysis followed a pseudo first order model, with apparent rate constants decreasing at higher SMT concentrations due to radical competition. Biodegradability assays revealed a substantial increase in the BOD5/COD ratio from initially low values to 0.34 after 300 min of pretreatment, indicating improved suitability for biological post-treatment. Overall, the electro/Fe3+/PDS process represents an efficient pre-oxidation strategy for the removal of refractory antibiotics from aqueous media.