In this paper, molecular dynamics simulations are performed to study the annealing process of γ-TiAl alloy with different parameters after introducing residual stress into prepressing. By mainly focusing on the dynamic evolution process of microdefects during annealing and the distribution of residual stress, the relationship between microstructure and residual stress is investigated. The results show that there is no phase transition during annealing, but atom distortion occurs with the change of temperature, and the average grain size slightly increases after annealing. There are some atom clusters in the grains, with a few point defects, and the point defect concentration increases with the rise in temperature, and vice versa; the higher the annealing temperature, the fewer the point defects in the grain after annealing. Due to the grain boundary volume shrinkage and and an increase in the plastic deformation of the grain boundaries during cooling, stress is released, and the average residual stress along Y and Z directions after annealing is less than the average residual stress after prepressing.
7 November 2019 in Modelling and Simulation in Materials Science and Engineering
In this paper, molecular dynamics (MD) simulations are performed to study the influence of residual stress on fracture behavior in γ -TiAl alloy with ∑3(111) twin boundaries. The tensile processes are simulated at 1, 300, 1050 K after the residual stress is introduced by prepressing. The evolution of microdefects during tensile fracture is observed, and the distribution of residual stress in three direction is characterized. Results show that the introduced residual stress is symmetrically distributed on both sides of ∑3(111) twin boundaries. The residual compressive stress can prevent the nucleation of micro-cracks and increase the yield strength. The fracture mode of the γ -TiAl alloy with ∑3(111) twin boundaries during tensile load at 1 K is the nucleation of microcracks at grain boundaries followed by intergranular fracture. The ∑3(111) twin boundaries have good thermal stability. The residual compressive stress is completely released and the amplitude of residual tensile stress increases at 1050 K, and the γ -TiAl alloy with ∑3(111) twin boundaries exhibits good ductility.
Titanium alloy thin-walled components are extensively used in aerospace engineering, yet their milling stability remains a persistent challenge due to vibration-induced surface anomalies. This study develops an advanced dynamic model for the face milling of titanium alloy thin-walled structures, systematically integrating axial cutting dynamics with regenerative chatter mechanisms and nonlinear process damping phenomena. The proposed framework crucially accounts for time-varying tool–workpiece interactions and damping characteristics, enabling precise characterization of stability transitions under dynamically varying axial immersion conditions. A novel extension of the semi-discretization method is implemented to resolve multi-parameter stability solutions, establishing a computational paradigm for generating three-dimensional stability lobe diagrams (3D SLDs) that concurrently evaluate spindle speed, cutting position, and the axial depth of a cut. Comprehensive experimental validation through time-domain chatter tests demonstrates remarkable consistency between theoretical predictions and empirical chatter thresholds. The results reveal that process damping significantly suppresses chatter at low spindle speeds, while regenerative effects dominate instability at higher speeds. This work provides a systematic framework for optimizing machining parameters in thin-walled component manufacturing, offering improved accuracy in stability prediction compared to traditional two-dimensional SLD methods. The proposed methodology bridges the gap between theoretical dynamics and industrial applications, facilitating efficient high-precision machining of titanium alloys.
Machining deformation caused by the release of residual stress during the processing of large-scale 7050 aluminum alloy thin-walled components remains a critical bottleneck, limiting high-quality and high-precision manufacturing and significantly compromising the dimensional stability of the parts. As a novel stress-control technique, ultrasonic treatment has been proven effective in improving the residual stress distribution within aluminum alloys, thereby reducing the machining deformation of thin-walled structures. However, a systematic analysis of the dynamic evolution and underlying release mechanisms of residual stress under ultrasonic action is still lacking. To analyze defect evolution and the origins of milling-induced residual stress, a molecular dynamics model of milling for 7050 aluminum alloy containing η-phase (MgZn₂ precipitates) was constructed. Following the simulation of the stress release process under ultrasonic treatment, our results reveal that the reduction and homogenization of residual stress are fundamentally attributed to dislocations absorbing energy within the applied ultrasonic field. This energy absorption activates dislocations, enabling them to overcome the potential energy barrier for motion. Consequently, extensive annihilation reactions occur primarily among Shockley partial dislocations, leading to a decrease in the total dislocation density. Ultimately, the internal stress of the material is relaxed and released through plastic deformation mediated by these dislocation reactions.
Aiming at the problem that the dimension error is difficult to control after wire cutting of TC4 alloy parts, a scheme for measuring the residual stress of TC4 alloy seeker based on ultrasonic critical refraction longitudinal wave method is proposed. The residual stress distribution after wire cutting and the distribution of secondary wire cutting after stress release were measured respectively. Combined with three-coordinate measuring error, the deformation law under different residual stress distribution is analyzed. The results show that the deformation error of seeker can be controlled by reducing the amplitude of residual tensile stress introduced by wire cutting.