This paper focuses on indirect biomass drying. It compares the operating characteristics of a laboratory-scale drum dryer and a pilot-scale rotary dryer. Before the design of an industrial dryer for a specific material, it is important to experimentally prove the process and to determine the drying characteristics of the material. To verify the portability of experimental results for indirect dryers, a drum dryer with indirect electric heating in a laboratory scale was designed and built to test and study the process of indirect drying. Based on the results obtained on a small-scale device, a prototype of a pilot steam-heated rotary dryer was designed and manufactured. A broad range of experiments with green wood chips and wet bark from open-air storage with moisture contents of 50 to 65 wt % were carried out on both dryers. The drying curves indicating the process, the square and volumetric evaporation capacities, and the drying energy consumption were obtained and compared, and the feasibility of indirect drying for these tested types of biomass was confirmed.
This article deals with the influence of the final drying degree of moist biomass used as fuel in a power or CHP plant on indirect dryer sizing. For a description of the drying process, experiments with wet bark containing approx. 50 wt% of water were carried out in a laboratory indirect dryer. A new parameter called drying effectivity was introduced, whose size varies according to the degree of biomass being dried. Its maximum value corresponds to the optimal biomass drying, when the relative size of the indirect dryer to evaporate the required mass of water from the biomass would be smallest. Based on the experimentally determined drying characteristics of wet bark, the optimal drying of 13 wt% of water content was evaluated. If the bark was dried to a lower water content, the required relative size and price of the dryer would increase. Similarly, drying a bark with water content above 31 wt% is not very advantageous because drying effectivity continues to increase rapidly at this stage, and the required relative size of the dryer therefore decreases.
The article describes the influence of additional installation of the combustion air humidifier for a biomass hot water boiler, which is equipped with a flue gas spray condenser, on its operating parameters and the heat supplied to the district heating system. Humidification of the air is carried out by spraying with water heated in the flue gas condenser, which is pre-cooled in the exchanger for preheating the return water from the district heating system. The case of the additional installation of the combustion air humidifier to the biomass hot water boiler USTSEN type JUE-FVB 7.2 with a heat output of 8 MW equipped with flue gas spray condenser is analyzed. Humidification and preheating of the combustion air leads to fuel savings and an increase in the dew point temperature of the flue gas, which improves the conditions for utilizing the waste heat from the flue gas in the condenser, as the heat is available at a higher temperature level. Humidification of the combustion air also affects the operating parameters of the boiler. In particular, the flue gas outlet temperature and flow rate increase and the efficiency of the boiler decreases slightly. Fuel consumption, however, decreases due to the heat input in the preheated and humidified combustion air. The application of the proposed solution would increase the heat supplied to the district heating system, by about 7 %–9 % of the boiler nominal heat output, depending on the heating of the air in the humidifier. A summer drop in biomass moisture would be reflected in a reduction in the energy benefit of the flue gas condenser by more than 20 %. However, humidification of the combustion air can limit this negative effect.
The condensation of water vapor from flue gas in the energy cycles of power and heating plants is an important issue to increase the efficiency of the boiler or to separate water vapor from flue gas. A theoretical study of flue gas condensation from biomass boilers in vertical tube condensers was conducted. An overview of the methods available for determining the condensation heat transfer coefficient was compiled. Three approaches were identified to determine the heat transfer coefficient and condenser heat output according to the foundation of each method: experimental foundation (Empirical correlations), semi-theoretical foundation (Heat and mass transfer analogy, Diffusion layer model) and theoretical foundation (Boundary layer model). Empirical correlations represent the simplest way to predict the condensation heat transfer coefficient. However, the deviation of the predicted results from the experimental results is quite high, and since the equations usually lack some important driving parameters or are developed for a slightly different geometry of operating conditions, they are not reliable enough for the considered application. The Boundary layer model is very complex and impractical. Therefore, the use of the Heat and mass transfer analogy or the Diffusion layer model is the most effective for the mentioned application.
In this work, the heat transfer in double pipe heat exchangers (DPHEs) with small tube spacing is analyzed. This type of heat transfer is generally described in many literary sources; however, in laminar flow, the resulting values of the theoretical equations differ. Moreover, the small spacing of the pipes can affect the fluid flow and subsequent heat transfer. The suitability of using available theoretical methods for the design of double pipe heat exchangers (the Stephan, VDI, and Baehr methods) was evaluated. A series of experiments was carried out on a double pipe heat exchanger with a tube spacing of 1.4 mm. The experimentally determined value of the heat transfer coefficient (HTC) was up to two times higher in comparison with the values calculated according to theoretical methods. The relative increase was more significant for the lower Reynolds number values. At the same time, the difference of the wall temperature along the circumference of the outer tube was detected. This phenomenon was theoretically analyzed and can be explained by tube misalignment in the small tube spacing. The procedure of quantification of this effect was proposed. This effect may cause an inhomogeneity of the media flow and temperature distribution and, as a result, increase the performance of the heat exchanger by tens of percent.