Giovanni Cascante

Dr. Giovanni Cascante


Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 August 2021 in Geotechnical Testing Journal
Verified
Journal Article
Closed access
CFCristiana Ferreira
Cristiana Ferreira
FDFredy Díaz-Durán
Fredy Díaz-Durán
VFViana Da Fonseca
Viana Da Fonseca
GCGiovanni Cascante
Giovanni Cascante
Bender elements (BEs) have become a routine geotechnical laboratory tool for seismic wave velocity measurements. Since the 1980s, this testing technique has gained popularity, currently being available in many geotechnical laboratories worldwide in a variety of apparatuses. The advantage of simultaneously measuring small- and large-strain soil stiffnesses in each device and the easiness and low-cost implementation of BE are the main reasons for their common application. Although there is already a standardized procedure for BE testing (ASTM D8295-19, Standard Test Method for Determination of Shear Wave Velocity and Initial Shear Modulus in Soil Specimens Using Bender Elements), the use of high-frequency pulses for the simultaneous measurement of compressional (VP) and shear (VS) wave velocities is not considered. In contrast, the use of high-excitation frequencies is usually discouraged, as they tend to induce spurious participation of high-vibration modes in the BE response. However, this work shows that the use of higher vibration modes can be advantageous to evaluate P-wave velocities from standard BE testing. Thus, this paper presents a new approach for the concurrent measurements of VP and VS using a typical installation of BE. The new approach is first demonstrated by experimental measurements and subsequently validated using high-frequency laser vibrometer measurements of the actual BE deformation (nanometer scale) under different excitation frequencies. The laser vibrometer measurements show the displacements of the transmitter BE as a function of the input frequency in not only the horizontal but also in the vertical directions, demonstrating the generation of P-waves when higher vibration modes are excited. The measured VP values are shown to be in good agreement with the predicted values using Biot’s equations. Thus, the proposed methodology addresses the current knowledge gap in the use of BE for concurrent P-wave and S-wave velocity measurements. The generated wavelengths are large enough to travel through the soil skeleton instead of the pore water only.

1 February 2017 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
JCJavier Camacho-Tauta
Javier Camacho-Tauta
HAHassan Ali
Hassan Ali
GCGiovanni Cascante
Giovanni Cascante
VFViana Da Fonseca
Viana Da Fonseca
In bender-element (BE) testing, shear-wave velocities are measured using two main methods: time-domain analysis of vibration data from pulse excitation and frequency-domain analysis of vibration from sine-sweep excitation. The frequency-domain analysis can be performed automatically. However, its results show high variability because they are affected by different variables such as the frequency content of the excitation, the resonant frequency of the BE system, and the resolution of the frequency-domain analysis. The reliability of the frequency-domain method is studied in this paper using simplified mathematical models and experimental results from BEs, miniature accelerometers, and resonant-column (RC) tests. The mathematical models are used to understand the effects of different variables in the frequency-domain method. Both laboratory and numerical results show that amplification peaks in the transfer function of the BE system can significantly affect the estimation of the shear-wave velocity. A modified frequency-domain analysis is proposed to enhance the reliability of the method using a high-frequency narrowband excitation outside the resonant peaks of the BE system. Results from the modified frequency-domain analysis tests show less than 10% error in the measurement of the shear-wave velocity with respect to the RC results.


1 December 2021 in Journal of Composites for Construction
Verified
Journal Article
Closed access
PDF file
PWPiotr Wiciak
Piotr Wiciak
Maria Anna  PolakMaria Anna Polak
Maria Anna Polak
GCGiovanni Cascante
Giovanni Cascante
Glass fiber-reinforced polymer (GFRP) bars are a common alternative to steel reinforcement, offering economical and safety benefits of avoiding/limiting corrosion in traditionally reinforced concrete structures (e.g., parking garages, buildings, and bridges). However, estimating the life of GFRP structures represents a challenge for the construction industry. The experimental program described in this paper is designed to evaluate progressive damage of GFRP bars due to a highly alkaline environment using ultrasonic nondestructive testing (NDT). The evaluation of damage in GFRP bars is performed using a new methodology based on the analysis of relative changes not only in wave velocity and but also in wave amplitude. The actual displacement time histories (nm) generated by the ultrasonic transducers are directly measured with a high-frequency laser Doppler vibrometer. The measurement of the actual ultrasonic displacements as a function of frequency is a required step for the new amplitude-based approach used in this study. Finally, NDT results (low-strain measurements) are correlated with the reduction of shear strength obtained from destructive shear tests (large-strain measurements). The results show that ultrasonic parameters (e.g., wave velocity and amplitude) correctly capture deterioration in the GFRP bars, and for the samples studied, ultrasonic parameters can be used to estimate the shear strength reduction with the induced damage. The maximum error in the estimation of shear strength using ultrasonic measurements is less than 7%.

1 July 2016 in Geotechnical Testing Journal
Verified
Journal Article
Closed access
MFM. Finas
M. Finas
HAH. Ali
H. Ali
GCGiovanni Cascante
Giovanni Cascante
PVP. Vanheeghe
P. Vanheeghe
Dynamic properties of soils, such as shear wave velocity and damping, are some of critical parameters in the design of civil infrastructures subjected to vibrations from earthquakes and machine foundations. Bender element (BE) testing is used in the laboratory to determine shear wave velocity; however, there is no standard procedure for the interpretation of the results. The main limitation in BE testing is the correct estimation of the shear wave arrival time leading to uncertainty in the values of shear wave velocity. In this paper, three different automatic methods for the shear wave arrival time detection were tested. From these methods, a new procedure was proposed for the automatic determination of the shear wave arrival time using the Akaike information criterion. The method is tested on a series of bender element measurements giving less than 5 % error when the results were compared with the standard method for a signal-to-noise ratio higher than four.

1 August 2011 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
YYYanjun Yang
Yanjun Yang
GCGiovanni Cascante
Giovanni Cascante
Maria Anna  PolakMaria Anna Polak
Maria Anna Polak