Bender elements are used to measure the low-strain shear-wave velocity of soils in many geotechnical laboratories worldwide. Despite their popularity, the method remains without a standard, mainly owing to the difficulties in controlling the actual behaviour of the bender element inside the specimen. Previous experimental and analytical studies on the behaviour of bender elements have found evidence that the actual transmitter movement is not equal in shape or frequency content of the electrical signal used as the input excitation. Furthermore, the size and geometry of the specimen influence the response of these piezoelectric transducers. In this study, miniature accelerometers are used to measure the particle vibration inside specimens during bender elements tests, which were performed in a resonant column device. The comparison between shear wave velocities obtained by resonant column and miniature accelerometers tests allow a better interpretation of bender element testing. The sine pulse bender element test results showed good agreement with the resonant column measurements. The results show the importance of the resonant frequencies of the bender element and their influence on frequency domain analysis of bender element testing.
1 May 2020 in Soil Dynamics and Earthquake Engineering
In bender-element (BE) testing, shear-wave velocities are measured using two main methods: time-domain analysis of vibration data from pulse excitation and frequency-domain analysis of vibration from sine-sweep excitation. The frequency-domain analysis can be performed automatically. However, its results show high variability because they are affected by different variables such as the frequency content of the excitation, the resonant frequency of the BE system, and the resolution of the frequency-domain analysis. The reliability of the frequency-domain method is studied in this paper using simplified mathematical models and experimental results from BEs, miniature accelerometers, and resonant-column (RC) tests. The mathematical models are used to understand the effects of different variables in the frequency-domain method. Both laboratory and numerical results show that amplification peaks in the transfer function of the BE system can significantly affect the estimation of the shear-wave velocity. A modified frequency-domain analysis is proposed to enhance the reliability of the method using a high-frequency narrowband excitation outside the resonant peaks of the BE system. Results from the modified frequency-domain analysis tests show less than 10% error in the measurement of the shear-wave velocity with respect to the RC results.
Diatoms are microscopic algae with a skeleton called a frustule, formed chiefly of silica, and are found in almost all aquatic environments and climatic conditions. Diatomaceous soils (DSs) originate from frustule sedimentation. In civil works (design and construction), the uncommon values obtained from DSs are not completely understood. There needs to be more knowledge about the strength and compressibility of DSs. The stability of these deposits is still being determined. Definitions of substances such as diatoms, diatomaceous soils, diatomaceous earth, diatomaceous oozes, frustules, and diatomite need to be clarified. This document references construction processes that face problems such as differential settlements, pile rebounds, and irregular pore pressures due to frustules. This review analyzes multiple sets of results regarding the grain size distribution, specific gravity, consistency, plasticity, compressibility, and shear strength of DSs. It is concluded that the particle size distribution of DSs generally classifies them as silts. Particles are modified by the imposition of stresses (frustule breakage), which impacts compressibility. Microfossils take up stresses, restrict strains, and cause sudden increases in compressibility when their yield stress is exceeded. Currently, their strain mechanisms need to be better understood. The Gs decreases with increasing frustule content, given the high porosity of the skeletons. The intraparticle pores of the frustules explain the high liquid limit (LL) of DSs. DSs can have high shear strengths and large yield surfaces due to the “interlocking” phenomenon and the interparticle contacts’ high frictional component caused by their rough surface and high silica content.
Filtered tailing is a relatively-environmentally friendly technique due to the recovery of water during the process of dehydration. This technique was recently developed and therefore there are few studies available compared to research on conventional tailings. This work focuses on the behaviour of a filtered copper tailing under an unsaturated condition, studying the effect of self-compaction by self-weight which is triggered by the deposition process through 1D consolidation tests. In addition, the impact of confinement on the stiffness and shear strength was studied by means of unsaturated drained triaxial tests. The initial matric suction was determined based on soil-water characteristic curves for two initially loose dry densities and the water content at which the material leaves the dehydration process. The unsaturated consolidation tests showed that for vertical stresses above 100 kPa and with ratios between the applied matric suction and air entry value lower than twelve, the material approaches saturated condition, reaching up to 95% degree of saturation. On the other hand, for the unsaturated drained triaxial tests, the effect of the matric suction generates increases in the shear strength and the stiffness of the material up to 200% and 600%, respectively. However, the increase tends to disappear as confinement increases.
Usually, optimal percentages of additives used to improve the characteristics of soils, are determined by laboratory tests of different complexity. Then, these optimal combinations are used directly in the pavement structures, without analysis of time or scale differences between laboratory and field conditions. This paper presents the results of a full-scale accelerated pavement test on a base course that has been improved by using fly ash and an alkali activator. Initially, the main characteristics of the testing equipment are presented. The optimal amount of the different components was previously obtained by laboratory tests. The components were mixed, the material was extended and compacted in layers and a curing time was permitted. After that, a wheel loaded with a vertical hydraulic actuator, simulating a rear half-axis of a truck, passed on the top layer repeated times. During the test, vertical deformations of the surface were measured in several points along the track. Results after around 10000 loading repetitions were compared against simultaneous measurements on a non-treated material subjected to identical loading application, showing the advantages of the alkali activation in reducing deformability of base courses and the effect of variable natural wheatear conditions on both type of pavement structures