Beryllium-based intermetallic compounds, such as Be12Nb, are attracting growing interest for their high thermal stability and potential to replace pure beryllium as neutron reflectors and multipliers in both fission and future fusion reactors, with additional applications in metallurgy, aerospace, and hydrogen technology. The paper presents the results of an investigation of the thermal treatment and phase formation of the intermetallic compound Be12Nb from a mixture of niobium and beryllium powders in the temperature range of 800–1300 °C. The phase evolution was assessed as a function of sintering temperature and time. A nearly single-phase Be12Nb composition was achieved at 1100 °C, while decomposition into lower-order beryllides such as Be17Nb2 occurred at temperatures ≥1200 °C, indicating thermal instability of Be12Nb under vacuum. Careful handling of sintering in low vacuum minimized oxidation, though signs of possible BeO formation were noted. The findings complement and extend earlier reports on Be12Nb synthesis via plasma sintering, mechanical alloying, and other powder metallurgy routes, providing broader insight into phase formation and synthesis. These results provide a foundation for optimizing the manufacturing parameters required to produce homogeneous Be12Nb-based components and billets at an industrial scale. Additionally, they help define the operational temperature limits necessary to preserve the material’s phase integrity during application.
This work discusses the possibility of decomposing magnesium fluoride by ionized water vapor to form solid magnesium oxide and hydrogen gas in the reaction: MgF2 + H2O → MgO + 2HF. The technology and individual apparatuses of the plasma-chemical installation are described, and the influence of the fractional composition of magnesium fluoride powder on the productivity of the plasma conversion process is considered. To improve the efficiency of the plasma pyrolysis process, a method for making magnesium fluoride briquettes was developed. The completeness of the conversion process of magnesium fluoride to an oxide was evaluated by energy dispersive X-ray spectroscopy in the study of objects in scanning electron microscopy (SEM) and by X-ray diffractometry. It was found that the conversion process of magnesium fluoride to magnesium oxide has a relatively high degree of decomposition of magnesium fluoride fraction ≤75 µm. The use of the proposed processing method makes it possible to obtain pure magnesium oxide as a commercial product and to utilize fluorine-containing industrial waste.
Plasma-facing components of fusion facilities must withstand a wide range of operating loads. Their structural integrity is strongly affected by plasma particles, including deuterium (D), tritium (T), and helium (He), as well as by 14 MeV neutrons, steady-state heat fluxes, and recurrent intense transient thermal loads. In most current studies, the effects of individual operating factors—such as neutron irradiation, plasma exposure, and thermal loading—are investigated separately, allowing the contribution of each factor to changes in material properties to be evaluated. However, degradation mechanisms arising from the synergistic action of these factors require investigation using more sophisticated experimental methodologies. The present study aims to develop a methodology for the simulation testing of materials intended for fusion applications and at investigating the structural and phase stability of Be12Ti, as well as its deuterium sorption behavior, following high-energy irradiation with 14 MeV D+ ions. Irradiation was performed at ion flux densities of approximately 8.6 × 1014 ions·cm−2·s−1 and 1.06 × 1020 ions·cm−2·s−1. The irradiation-induced target temperatures reached approximately 400K and 1000K, respectively. An intermetallic Be12Ti alloy produced at the Ulba Metallurgical Plant in Kazakhstan was used as the target material. The selection of Be12Ti was motivated by existing fusion reactor concepts that consider this intermetallic compound as a neutron multiplier material, including the Japanese JA DEMO concept.
Beryllium-based intermetallic compounds are considered promising functional and structural materials for advanced nuclear systems due to their favorable neutronic, thermal and activation characteristics. In this work, neutron-induced activation in titanium and chromium beryllides (Be12Ti and Be12Cr) containing technological impurities was investigated under fission and fusion neutron environments. Experimental gamma-spectrometric measurements and Monte Carlo calculations were performed for specimens irradiated in the WWR-K research reactor. Agreement between calculated and measured specific activities for the dominant activation products Sc-46, Mn-54, Fe-59 and Cr-51 confirms the applicability of the neutronics approach. Neutron-induced gas production (He-4, He-3, T and Li-6) was additionally evaluated for an ITER-relevant D-T spectrum under fixed-fluence conditions. The results demonstrate pronounced spectrum-dependent differences in activation and transmutation behaviour and provide a basis for extrapolating fission-irradiation data to fusion-relevant conditions.