In this paper, a high step-up non-isolated DC-DC converter is proposed to provide high voltage-gain with low voltage-stress on semiconductors. The main feature of the proposed structure is its flexibility in providing constant output voltages with a reasonable range of voltage stress. This flexibility of the voltage-gain is achieved by different combinations of duty cycles. Also, this feature improves the efficiency of the proposed converter. This structure consists of three switches, two inductors, three capacitors and four diodes. In this paper, description of continuous conduction mode (CCM), discontinuous conduction mode (DCM), boundary condition mode (BCM), non-ideal model, and control method are presented. Comparisons between the proposed converter and other related structures show that in this converter, the voltage gain is improved and semiconductors voltage stresses are reduced. In order to verify the mathematical analysis, a 500W laboratory prototype of the proposed converter is built and its experimental results are investigated completely.
3 November 2021 in IEEE Transactions on Industrial Electronics
This article introduces a new coupled inductor based dual-input ultra-high step-up dc–dc converter with a high voltage conversion ratio, low voltage stress across semiconductor components, and high efficiency features. The coupled inductor and voltage multiplier circuit (VMC) techniques have been utilized to enhance the voltage gain. The blocking voltages of power switches are clamped by VMC at low values and can be controlled via the turn ratio of the coupled inductors that decreases the voltage rate of power switches and converter's cost. The presented dual-input structure can transfer power to the load from two independent voltage sources. Besides, the inputs and output ports are common ground, which can reduce the electromagnetic interference influences. Operation modes delineation, steady-state analysis, and comparison section are provided for describing the proposed structure performance. Finally, to confirm the effectiveness of the presented topology, experimental waveforms with a 200 W output power at 50 kHz switching frequency are presented.
18 August 2021 in IEEE Transactions on Industrial Electronics
In this article, a new triple-switch triple-mode (TS-TM) high step-up dc–dc converter is proposed. The proposed converter consists of three switches, four diodes, two magnetically coupled inductors, and three capacitors. This converter can provide a high voltage conversion ratio with high power efficiency and low voltage stress across the power semiconductor components. Due to the low voltage stresses of the power semiconductors and implementing the coupled inductors technique, the proposed converter is a low-cost and high-efficient structure in comparison to the other similar TS-TM structures. In order to clarify the advantages of the proposed converter, the required mathematical calculations and comparison results with similar converters are presented. Also, a novel TS-TM with transformer is proposed to overcome the electromagnetic interface problems. Furthermore, a 500 W experimental prototype is built and its performance with different values of duty cycles is tested to prove the claimed features of the proposed converter. A total of 94.5% maximum power efficiency of the assembled prototype has been obtained at 260 W output power.
4 November 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
This paper presents a high-step-up DC-DC topology. This circuit configuration yields a quadratic output voltage while maintaining low voltage stress on power MOSFETs. The configuration features a common ground connection among the input and output ports, with the sources of the switches directly linked to the ground. It has two switches, three diodes, four capacitors, and two coupled inductors. The first coupled inductor has three windings to increase voltage gain and limit input current ripple. The second one has two windings to increase voltage gain. Steady-state analysis is conducted to determine output voltage and voltage stress across power MOSFETs. The suggested topology’s key feature is its soft input current ripple, which is achieved using a coupled inductor configuration. A comparison section highlights its features compared to the state-of-the-art topologies reported in this paper. In addition, graphical voltage gain and voltage stress of power MOSFETs compared with other structures are added. The final step includes the development of a laboratory prototype, which operates under duty cycle variations of 0.3-0.6 for a wide input voltage range of 18-48 V. The prototype is tested for a maximum output power of 400W and a switching frequency of 50 kHz.
3 December 2021 in IEEE Transactions on Power Electronics
In this article, a new simple buck converter with zero voltage switching (ZVS) performance and almost zero output current ripple is proposed. The proposed structure's auxiliary circuit contains a capacitor and an inductor without any switches, which makes it possible to minimize the switching losses and eliminate other additional losses. The main power diode also turns off under zero current switching condition and the reverse recovery losses of the power diode is minimized. Eliminating the switching losses and the reverse recovery losses allows the converter to operate with high power efficiency, which makes it a good option for high power efficiency-required applications. In this article, five operational modes are explained. The design section includes the designing criteria of the components. Also, the efficiency analysis, control system for stabilizing the output voltage, and applying a variable inductor to ensure the soft-switching operation are analyzed. The comparison results are also discussed. Moreover, an experimental prototype of the proposed structure at 200 W output power and 75 kHz frequency is built to prove the above-mentioned advantages. Finally, the soft-switching waveforms are obtained for different output powers with various duty cycles and equal switching frequency to verify the ZVS performance of the converter at different loads and changes in input voltage and duty cycle.