Marek Tomasz Korzeniewski

Dr. Marek Tomasz Korzeniewski

orcid

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

13 October 2021 in Energies
Verified
Journal Article
Open access
PDF file
ASAndrzej Sikorski
Andrzej Sikorski
PFPiotr Falkowski
Piotr Falkowski
MKMarek Tomasz Korzeniewski
Marek Tomasz Korzeniewski
The article presents comprehensive results of research on two representative topologies of converters used in the path of processing energy generated in a wind turbine and transmitted to the grid. The topology T1 uses a two-level transistor-controlled rectifier as a converter from the generator side, while the T2 topology uses DC/DC boost converter. In both topologies, a three-level back-to-back converter with a line filter L was used as a grid converter. The conclusions indicate the tendency of changes in power losses depending on the aforementioned parameters and can be used at the stage of deciding on the choice of topology, operating parameters or selection of control methods depending on the specific operating conditions of the wind turbine.

1 December 2011 in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
Verified
Journal Article
Open access
PDF file
ASA. Sikorski
A. Sikorski
MKMarek Tomasz Korzeniewski
Marek Tomasz Korzeniewski
AC/DC/AC converter in a small hydroelectric power plant: The article discusses application of AC/DC/AC converter cooperating with an induction generator in small hydroelectric power plants. The induction generator works with power grid or a separated group of receivers, enabling to generate power even at low speeds of the turbine. The article provides also results of the investigation concerning the functioning of the generator coupled with AC/DC/AC converter in steady and transient states during start-up and voltage decay.

20 January 2013 in Automatika
Verified
Journal Article
Open access
PDF file
ASAndrzej Sikorski
Andrzej Sikorski
MKMarek Tomasz Korzeniewski
Marek Tomasz Korzeniewski
In the paper a new way of DTC control method analysis to explain flux and current distortion at a low speed of motor operation is discussed. As a result, a new DTC-d algorithm is proposed. It is important that the DTC-d algorithm uses the same switching table as the DTC method. The modified DTC algorithms are free from the disadvantages of the conventional DTC method i.e. hexagonal flux and strongly deformed current at a low speed range. The dynamical properties of the new algorithms are similar to the conventional DTC method. The correctness of the proposed methods has been confirmed by laboratory investigations.

1 September 2007
Verified
Conference Paper
Closed access
ASAndrzej Sikorski
Andrzej Sikorski
MKMarek Tomasz Korzeniewski
Marek Tomasz Korzeniewski
ARAdam Ruszczyk
Adam Ruszczyk
MKMarian P. Kazmierkowski
Marian P. Kazmierkowski
PAPatryk Antoniewicz
Patryk Antoniewicz
MJMarek Jasinski
Marek Jasinski
In the paper comparison of two classes of direct torque and flux control methods with linear (DTC-SVM) and nonlinear (DTC-δ, DTC-2x2, DTFC-3A) controllers was carried out. Criteria of comparisons in both steady and transient states in similar conditions i.e. at the same average switching frequency, were proposed. The comparisons were made using the results of laboratory tests of control systems cooperating with drive systems.

1 December 2013 in Bulletin Of The Polish Academy Of Sciences-Technical Sciences
Verified
Journal Article
Open access
PDF file
ASA. Sikorski
A. Sikorski
KKK. Kulikowski
K. Kulikowski
MKMarek Tomasz Korzeniewski
Marek Tomasz Korzeniewski
: This paper describes two modern direct torque and flux control methods of an induction machine supplied by a three-level inverter. Additionally, it presents a comparison of the methods both in static and dynamic states. The methods, in a specific way, make use of an increased number of active vectors of the three-level inverter in order to improve control quality and reduce switching frequency. The two methods modify the DTC method by using its advantages and eliminating, at the same time its drawbacks. In static states the comparison was based on the results of investigations performed for two different load values and three set values of angular speed, whereas in dynamic states the comparison was focused on the behavior of the machine at startup. The results of the investigations have shown that both methods give very good performance. They are characterized by both sinusoidal shape of flux and low current deformations even at low angular speeds i.e. less than 10% of the nominal value. The presented methods also allow to generate nominal flux for set zero angular speed in order to achieve excitation of the induction machine. The switching frequencies for both methods are very similar in almost the whole range of control but the methods have shown some differences in control quality, particularly for higher torque values.