To support the design of a two-dimensional turbine blade profile with reduced shock loss, an efficient model for shock system with separation shock in highly loaded turbine cascade needed to be established to realize parameterized shock losses prediction and analysis. The discussions on the model demonstrate that the effect of base pressure on shock losses can be achieved by controlling the width of the base region (the region between the pressure surface and suction surface trailing edge separation points). Increasing the trailing-edge wedge angle can increase the base pressure as well as the width of the base region, thus reducing the shock losses. Moreover, the pressure change caused by reducing the suction surface curvature downstream of the throat can reduce the loss caused by the reflected shock.
To address the thermal protection challenges of multiple high-temperature components and the electrical power deficiency in hypersonic vehicles, this study proposes twelve multi-heat-source thermoelectric conversion schemes based on the sCO2 Brayton cycle. A three-dimensional evaluation system for thermal management is established, incorporating thermal efficiency, coolant mass flow rate, and system mass as key metrics. A comprehensive parameter sensitivity analysis was conducted on the twelve dual-heat-source cycle configurations. For systematic performance comparison, the Non-dominated Sorting Genetic Algorithm II (NSGA-II) was employed for multi-objective optimization, with Pareto fronts analyzed to determine optimal configurations. The results demonstrate that appropriately increasing the minimum cycle temperature can significantly reduce coolant flow requirements. Multi-objective optimization reveals the following: (1) The pre-compressed aero-comb configuration achieves optimal performance in the efficiency-mass flow rate optimization scenario; (2) Both pre-compressed aero-comb and re-compressed comb-aero configurations show superiority in the efficiency-mass optimization scenario; (3) The pre-compressed aero-comb configuration exhibits lower system mass in low coolant flow regions for the mass flow rate-mass optimization scenario. Overall, the performance of the precompression aero-comb configuration is relatively superior. This work provides an important reference for the design of thermal management systems for hypersonic vehicles.
4 March 2025 in IEEE Transactions on Instrumentation and Measurement
Accurate measurement of the axial clearance between the rotor and stator in an aeroengine is crucial for precise engine design and aerodynamic analysis. It also provides a significant reference for correcting measurements obtained through other non-contact methods. This paper proposes a Triangulation Method Based on Time-of-Arrival (TMBT) for measuring axial clearance, which can simultaneously measure rotor speed and has the potential to replace traditional once-per-revolution (OPR) sensors. The mechanism of measurement error is analyzed, and methods for error estimation and correction are proposed. A simulated rotor test bench was set up in the laboratory to achieve dynamic calibration and performance testing of the sensor, and to verify the effectiveness of the error estimation and correction methods. Experimental results show that the measurement accuracy of this method is better than 0.05mm (for a range of 2.5–8.0 mm) and better than 1.5% (for a range of 2.5–11.0 mm). The proposed error estimation and correction methods effectively estimate and correct measurement errors caused by sensor installation positional offsets.
The endwall clearance of adjustable guide vanes in variable geometry turbines (VGTs) is often simplified as a uniform or averaged value, whereas actual vane rotation about a pivot produces a chordwise non-uniform clearance distribution. This study investigates the formation and aerodynamic consequences of rotation-induced non-uniform clearance, aiming to identify the leakage-controlling region and provide guidance for pivot layout and clearance control. A geometry-based parametric representation is developed, and numerical simulations combined with orthogonal design and analysis of variance are used to quantify the effects of clearance parameters in different chordwise regions. The results show that averaged clearance alone is insufficient to characterize the aerodynamic response: configurations with similar mean clearance can produce more than 25% variation in leakage mass flow rate. The mid-chord region, approximately 40%–80% of the axial chord, is identified as the leakage-controlling region (LCR), contributing 62.6%–66.9% of the total leakage mass flow. This region also corresponds to the strongest leakage–mainstream momentum exchange and the primary source of downstream loss accumulation. Under transonic conditions, shock–leakage interaction increases the sensitivity of trailing-edge clearance, but the dominant role of the LCR remains unchanged. Further analysis of realistic vane adjustment shows that pivot layout affects endwall loss by controlling both clearance redistribution and local leakage development within the LCR. These findings indicate that VGT endwall design should focus on controlling clearance evolution in the LCR, providing a physics-based basis for pivot layout and clearance management.
Ultra-low-temperature frosting is a critical issue in pre-cooled hypersonic propulsion systems, where rapid cooling by cryogenic fuels can cause frost accumulation on precooler tube bundles. However, conventional frost-growth models, predominantly developed for isothermal flat surfaces and long-duration frosting, are not directly applicable to the highly transient cryogenic conditions of precoolers. In this study, vertically aligned parallel cylinders were employed as a representative tube-bundle geometry, with liquid nitrogen used to reproduce the rapid wall-temperature decrease from ambient to cryogenic conditions. Frost-thickness evolution was measured experimentally, while schlieren visualization was introduced to reveal the surrounding flow and vapor-transport induced behavior associated with frost development. The experiments revealed a strong correspondence between the initial frost-growth rate and the cooling rate at the frost-layer base. A simplified theoretical analysis yielded a semi-quantitative scaling relation that captures the observed dependence of frost growth on the dominant thermal parameters. Schlieren observations further revealed vortical motion within the cold boundary layer near the frost/air interface at the bottom, indicating that vortical transport plays an important role in promoting spatially uniform frost growth between adjacent vertical cylinders. These findings provide experimental insight into the thermal and fluid-dynamic mechanisms governing the initial stage of ultra-low-temperature frosting and establish a physical basis for future quantitative modeling and frost-mitigation strategies in cryogenic precoolers.
Accurate measurement of rotor blade tip clearance (BTC) is critical for aeroengine performance and safety. This paper presents two-dimensional models for predicting signals from a skewed-dual-light-probe (SDLP) used in laser triangulation-based Blade Tip Timing (BTT) systems. The models, based on total specular and diffuse reflection assumptions, simulate pulse signals generated in dual channels as a blade traverses the SDLP. A virtual SDLP is calibrated, and an experimental setup simulating blade translation validates the models. Results demonstrate that both models yield linear calibration curves for BTC measurement, with the diffuse reflection model showing closer alignment to experimental data. These models provide valuable insights for SDLP design, blade tip geometry, and sensor placement, offering significant potential for enhancing BTC measurement accuracy in aeroengine applications.