Xianlong Lu

Dr. Xianlong Lu


Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2019 in Journal of Geotechnical and Geoenvironmental Engineering
Verified
Journal Article
Closed access
ZQZeng-Zhen Qian
Zeng-Zhen Qian
XLXianlong Lu
Xianlong Lu
WYWen-Zhi Yang
Wen-Zhi Yang
Comparative field tests were carried out on two straight-sided piers and two belled piers under combined uplift and lateral loads on arid loess sloping ground with an inclination angle of 20°. The pier-head uplift and lateral displacements, ground surface deformation, and soil pressures on the pier and bell were obtained. For both straight-sided and belled piers on sloping ground under combined uplift and lateral loads, the curves of the applied loads versus pier-head uplift displacement and pier-head lateral deflection exhibited an initial linear segment, a curvilinear transition, and a final linear region, and their capacities should be interpreted from the load test results. The pier-head uplift displacement and pier-head lateral deflection increased nearly at the same displacement increment, and the limit state of a pier on a slope under a combined uplift-lateral load may be primarily governed by the pier-head lateral deflection due to lateral soil failure. Belling may cause greater load-transfer depths and can effectively mobilize more soil to resist the combined uplift and lateral loads, and additional pier embedment in a slope can increase the uplift and lateral resistance to match the level-ground capacity for both straight-sided and belled piers.

10 September 2018 in Arabian Journal for Science and Engineering
Verified
Journal Article
Closed access
PDF file
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
MSMing-Qiang Sheng
Ming-Qiang Sheng

15 December 2023 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
XLXianlong Lu
Xianlong Lu
QYQiang Yu
Qiang Yu
JXJiayu Xu
Jiayu Xu
BYBing Yue
Bing Yue
MSMingqiang Sheng
Mingqiang Sheng
Because of the existence of clay minerals such as montmorillonite in red clay, the strength of red clay decreases significantly as water content increases. This study aims to improve the strength of red clay by using three different kinds of industrial solid waste powder, i.e., steel slag (SS) powder, fly ash (FA), and ground-granulated blast furnace slag (GGBS). At the same time, the ordinary Portland cement (OPC) was selected as a comparison of the improvement effect on the strength of red clay modified by the aforementioned industrial solid waste powder. The properties of the red clay and the industrial solid waste powder were documented comprehensively. The unconfined compressive strength (UCS) tests were conducted on the specimens of the red clay and the red clay modified by the OPC, SS, FA, and GGBS, which had been cured for 3, 7, and 21 days at a temperature of 25°C, respectively. The results showed that the strength of red clay can be significantly improved by the three kinds of industrial solid waste powder. After a 21-day curing period, the experimental results showed that the UCS of the red clay modified by 7% SS, 5% FA, and 5% GGBS increased by 252%, 131%, and 140% compared to that of the red clay without modification. However, the modification effects of the SS, FA, and GGBS on the red clay were generally inferior to that of the OPC. By observing the microstructures of the modified clay, the mechanism of industrial solid waste powder and cement improving the strength of the red clay was analyzed. The findings in this study can provide a reference for improving subgrade strength by a soil-modification method in road constructions.

25 July 2025 in Materials
Verified
Journal Article
Open access
PDF file
ZXZilu Xie
Zilu Xie
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
BYBing Yue
Bing Yue
WSWendi Su
Wendi Su
MTMengze Tian
Mengze Tian
This study developed a full solid waste-based cementitious material (ISWs-CM) using steel slag (SS), ground granulated blast furnace slag (GGBFS), phosphorus slag (PS), carbide slag (CS), and desulfurized gypsum (DG) to completely replace cement. A two-layer optimization strategy, combining three chemical moduli and simplex lattice experiments, was employed to determine the proportion and to investigate the impact of proportions on the uniaxial compressive strength of mortar. As an application case, the ISWs-CM with the optimal proportion was employed to stabilize aeolian sand, and its effectiveness as a cement substitute and the underlying mechanisms were investigated. The results indicated that the ISW proportion that maximized the strength of the mortar was SS:GGBFS:PS:CS = 5:20:20:40. The strength of the mortar was enhanced when the proportion of GGBFS exhibiting the highest reactivity was increased and also increased initially and then decreased with an increase in CS when the dosage of GGBFS was fixed. The aeolian sand stabilized by ISW-CM exhibited higher strength than that stabilized with cement. The greater number and variety of hydration products resulted in denser connections and encapsulation of sand particles, which highlights the synergistic effect of ISWs and the potential of ISW-CM as a cement replacement across diverse applications including aeolian sand stabilization.

4 September 2025 in Gels
Verified
Journal Article
Open access
PDF file
ZXZilu Xie
Zilu Xie
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
HWHao Wang
Hao Wang
LPLAI PHATYOUFY
LAI PHATYOUFY
Aeolian sand is the primary geological material for construction in desert regions, and its stabilization with industrial solid wastes-based geopolymer (ISWG) provides an eco-friendly treatment replacing cement. This study comparatively investigated the enhancement effects of chemical activators and expansive agents on compressive strength of aeolian sand stabilized by ISWG (ASIG). Three chemical activators—NaOH, Ca(OH)2, and CaCl2—along with two expansive agents—desulfurized gypsum and bentonite—were considered. Through X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, mercury intrusion porosimetry and pH values tests, the enhancement mechanisms of the additives on ASIG were elucidated. Results demonstrate that the expansive agent exhibits significantly superior strengthening effects on ASIG compared to the widely applied chemical activators. Chemical activators promoted ISWs dissolution and hydration product synthesis, thereby densifying the hydration product matrix but concurrently enlarged interparticle pores. Desulfurized gypsum incorporation induced morphological changes in ettringite, and excessive desulfurized gypsum generated substantial ettringite that disrupted gel matrix. In contrast, bentonite demonstrated superior pore-filling efficacy while densifying gel matrix through a compaction effect. These findings highlight bentonite superior compatibility with the unique microstructure of aeolian sand compared to conventional alkaline activators or expansive agents, and better effectiveness in enhancing the strength of ASIG.

1 January 2021 in Advances in Civil Engineering
Verified
Journal Article
Open access
PDF file
MSMingqiang Sheng
Mingqiang Sheng
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
This study elucidates the compression behavior of a type of composite foundation of spread footing anchored by helical anchors. Three composite foundations were installed at a field site, and compression load testing was carried out on each foundation. Both the site conditions and the load tests were documented comprehensively. The compression load‐settlement curves of composite foundations exhibit an initial linear‐elastic segment, a curve transition, and a final linear region, and their capacities should be interpreted from the load‐settlement curves. Five representative interpretation criteria (Chin, Terzaghi and Peck, slope tangent, tangent intersection, and L1–L2) were employed to determine the capacity of each foundation. Both the helical anchors and the footing share compression loadings on the composite foundation. Soil pressure cells at the center, near the edge, and at the corner of the footing represent a distribution from the lower, middle, and higher ranges of incremental soil pressures underneath the footing. Helical anchors underneath the footing approximately share 60%–80% of total load applied on the composite foundation pier, and higher compression resistance of a composite foundation can be obtained by increasing the footing embedment depth and the number of helical anchors underneath the footing.