Zilu Xie

Mr. Zilu Xie


Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 July 2025 in Materials
Verified
Journal Article
Open access
PDF file
ZXZilu Xie
Zilu Xie
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
BYBing Yue
Bing Yue
WSWendi Su
Wendi Su
MTMengze Tian
Mengze Tian
This study developed a full solid waste-based cementitious material (ISWs-CM) using steel slag (SS), ground granulated blast furnace slag (GGBFS), phosphorus slag (PS), carbide slag (CS), and desulfurized gypsum (DG) to completely replace cement. A two-layer optimization strategy, combining three chemical moduli and simplex lattice experiments, was employed to determine the proportion and to investigate the impact of proportions on the uniaxial compressive strength of mortar. As an application case, the ISWs-CM with the optimal proportion was employed to stabilize aeolian sand, and its effectiveness as a cement substitute and the underlying mechanisms were investigated. The results indicated that the ISW proportion that maximized the strength of the mortar was SS:GGBFS:PS:CS = 5:20:20:40. The strength of the mortar was enhanced when the proportion of GGBFS exhibiting the highest reactivity was increased and also increased initially and then decreased with an increase in CS when the dosage of GGBFS was fixed. The aeolian sand stabilized by ISW-CM exhibited higher strength than that stabilized with cement. The greater number and variety of hydration products resulted in denser connections and encapsulation of sand particles, which highlights the synergistic effect of ISWs and the potential of ISW-CM as a cement replacement across diverse applications including aeolian sand stabilization.

1 April 2025 in Applied Sciences
Verified
Journal Article
Open access
PDF file
ZXZilu Xie
Zilu Xie
ZQZengzhen Qian
Zengzhen Qian
HWHao Wang
Hao Wang
YQYingzhe Qi
Yingzhe Qi
BYBing Yue
Bing Yue
Aeolian sand serves as the principal foundation material for construction in desert regions, yet its stabilization predominantly relies on cement, presenting critical carbon emission challenges. This study developed a cementitious material utilizing complementary industrial solid wastes (ISWs)—steel slag (SS), ground granulated blast-furnace slag (GGBFS), phosphorus slag (PS), and carbide slag (CS)—based on clinker three chemical moduli (TCM) and simplex lattice design, aiming to replace cement for aeolian sand stabilization. ISW dosage effects on stabilized sand strength and mechanical properties were investigated, with stabilization mechanisms studied via phase and microstructural analysis. Results demonstrated that GGBFS exerted the most significant positive influence on the strength of stabilized sand. The optimal proportion was determined as SS:GGBFS:PS:CS = 5:35:20:40, achieving strength comparable to cement-stabilized aeolian sand in the literature. The elastic modulus and ductility of stabilized sand exhibited linear positive and exponential negative correlation with uniaxial compressive strength. The hydration products of ISWs, including C(-A)-S-H gel and ettringite similar to clinker, effectively enhanced interparticle bonding strength and pore-filling capacity. ISW proportions governed the composition and distribution of hydration products, thereby modulating microstructural density and strength, ultimately dictating macroscopic performance variations. The conclusions provide an environmentally friendly solution for aeolian sand stabilization in desert regions.

4 September 2025 in Gels
Verified
Journal Article
Open access
PDF file
ZXZilu Xie
Zilu Xie
ZQZengzhen Qian
Zengzhen Qian
XLXianlong Lu
Xianlong Lu
HWHao Wang
Hao Wang
LPLAI PHATYOUFY
LAI PHATYOUFY
Aeolian sand is the primary geological material for construction in desert regions, and its stabilization with industrial solid wastes-based geopolymer (ISWG) provides an eco-friendly treatment replacing cement. This study comparatively investigated the enhancement effects of chemical activators and expansive agents on compressive strength of aeolian sand stabilized by ISWG (ASIG). Three chemical activators—NaOH, Ca(OH)2, and CaCl2—along with two expansive agents—desulfurized gypsum and bentonite—were considered. Through X-ray diffraction, thermogravimetric analysis, scanning electron microscopy, mercury intrusion porosimetry and pH values tests, the enhancement mechanisms of the additives on ASIG were elucidated. Results demonstrate that the expansive agent exhibits significantly superior strengthening effects on ASIG compared to the widely applied chemical activators. Chemical activators promoted ISWs dissolution and hydration product synthesis, thereby densifying the hydration product matrix but concurrently enlarged interparticle pores. Desulfurized gypsum incorporation induced morphological changes in ettringite, and excessive desulfurized gypsum generated substantial ettringite that disrupted gel matrix. In contrast, bentonite demonstrated superior pore-filling efficacy while densifying gel matrix through a compaction effect. These findings highlight bentonite superior compatibility with the unique microstructure of aeolian sand compared to conventional alkaline activators or expansive agents, and better effectiveness in enhancing the strength of ASIG.